- 您現在的位置：買賣IC網 > PDF目錄10789 > LTC2870IFE#PBF (Linear Technology)IC TXRX RS485/RS422 28-TSSOP PDF資料下載
參數資料
| 型號： | LTC2870IFE#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 13/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS485/RS422 28-TSSOP |
| 產品培訓模塊： | LTC2870 and LTC2871 Multi-Protocol Transceivers |
| 標準包裝： | 50 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 2/2 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 3 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 28-TSSOP 裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC2870/LTC2871
20
28701f
Inrush Current and Supply Overshoot Precaution
In certain applications fast supply slew rates are generated
when power is connected. If the VCC voltage is greater
than 4.5V and its rise time is faster than 10μs, the pins
VDD and SW can exceed their absolute maximum values
during start-up. When supply voltage is applied to VCC, the
voltage difference between VCC and VDD generates inrush
current flowing through inductor L1 and capacitors C1 and
C2. The peak inrush current must not exceed 2A. To avoid
this condition, add a 1Ω resistor as shown in Figure 14.
This precaution is not relevant for supply voltages below
4.5V or rise times longer than 10μs.
VL Logic Supply and Logic Pins
A separate logic supply pin VL allows the LTC2870 and
LTC2871 to interface with any logic signal from 1.7V to
5.5V. All logic I/Os use VL as their high supply. For proper
operation, VL should not be greater than VCC. During
power-up, if VL is higher than VCC, the device will not be
damaged, but behavior of the device is not guaranteed.
If VL is not connected to VCC, bypass VL with a 0.1μF
capacitor to GND.
RS232 and RS485 driver outputs are undriven and the
RS485 termination resistors are disabled when VL or VCC
is grounded or VCC is disconnected.
Although all logic input pins reference VL as their high
supply, they can be driven up to 7V, independent of VL and
VCC, with the exception of FEN, which must not exceed VL
by more than 1V for proper operation. Logic input pins
do not have internal biasing devices to pull them up or
down. They must be driven high or low to establish valid
logic levels; do not float.
RS485 Driver
The RS485 driver provides full RS485/RS422 compati-
bility. When enabled, if DI is high, Y – Z is positive. With
the driver disabled the Y and Z output resistance is greater
than 96kΩ (typically 125kΩ) to ground over the entire
common mode range of –7V to +12V. This resistance is
equivalent to the input resistance on these lines when the
driver is configured in half-duplex mode and Y and Z act
as the RS485 receiver inputs.
Driver Overvoltage and Overcurrent Protection
The RS232 and RS485 driver outputs are protected from
short circuits to any voltage within the absolute maximum
range ±15V. The maximum current in this condition is 90mA
for the RS232 driver and 250mA for the RS485 driver.
If the RS485 driver output is shorted to a voltage greater
than VCC, when it is active, positive current of up to 100mA
may flow from the driver output back to VCC. If the system
power supply or loading cannot sink this excess current,
clamp VCC to GND with a Zener diode (e.g., 5.6V, 1W,
1N4734) to prevent an overvoltage condition on VCC.
APPLICATIONS INFORMATION
Figure 14. Supply Current Overshoot Protection
for Input Supplies of 4.5V of Higher
28701 F14
0V
5V
≤10μs
C1
220nF
L1
10μH
INRUSH
CURRENT
C4
2.2μF
R1
1Ω
1/8W
VCC
VDD
GND
SW
CAP
C2
1μF
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BNJ-MX-F3 | CONVERTER MOD DC/DC 36V 75W |
| VE-JTV-MY-S | CONVERTER MOD DC/DC 5.8V 50W |
| LTC1597BIG#TRPBF | IC D/A CONV 16BIT PAR 28-SSOP |
| VI-BNJ-MX-F2 | CONVERTER MOD DC/DC 36V 75W |
| VE-JTT-MY-S | CONVERTER MOD DC/DC 6.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2870IUFD#PBF | 功能描述:IC TXRX RS485/RS422 28-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| LTC2870IUFD#TRPBF | 功能描述:IC TXRX RS485/RS422 28-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| LTC2871CFE#PBF | 功能描述:IC TXRX RS485/RS422 38-TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1 系列:- 類型:線路收發器 驅動器/接收器數:5/3 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:Digi-Reel® 產品目錄頁面:918 (CN2011-ZH PDF) 其它名稱:296-25096-6 |
| LTC2871CFE#TRPBF | 功能描述:IC TXRX RS485/RS422 38-TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| LTC2871CUHF#PBF | 功能描述:IC TXRX RS485/RS422 38-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
發布緊急采購，3分鐘左右您將得到回復。