- 您現在的位置：買賣IC網 > PDF目錄377774 > LTC3206EUF (LINEAR TECHNOLOGY CORP) I2C Multidisplay LED Controller PDF資料下載
參數資料
| 型號： | LTC3206EUF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | I2C Multidisplay LED Controller |
| 中文描述： | LED DISPLAY DRIVER, BCC24 |
| 封裝： | 4 X 4 MM, 0.75 MM HEIGHT, PLASTIC, QFN-24 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 204K |
| 代理商： | LTC3206EUF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
LTC3206
8
3206f
Byte Format
Each byte sent to the LTC3206 must be 8 bits long followed
by an extra clock cycle for the Acknowledge bit to be
returned by the LTC3206. The data should be sent to the
LTC3206 most significant bit (MSB) first.
Acknowledge
The Acknowledge bit is used for handshaking between the
master and the slave. An Acknowledge (active LOW)
generated by the slave (LTC3206) lets the master know
that the latest byte of information was received. The
Acknowledge related clock pulse is generated by the
master. The master releases the SDA line (HIGH) during
the Acknowledge clock cycle. The slave-receiver must pull
down the SDA line during the Acknowledge clock pulse so
that it remains a stable LOW during the HIGH period of this
clock pulse.
Slave Address
The LTC3206 responds to only one 7-bit address which
has been factory programmed to 0011011. The eighth bit
of the address byte (R/W) must be 0 for the LTC3206 to
recognize the address since it is a write only device. This
is equivalent to an 8-bit address where the least significant
bit of the address is always 0. If the correct seven bit
address is given but the R/W bit is 1, the LTC3206 will not
respond.
Bus Write Operation
The master initiates communication with the LTC3206
with a START condition and a 7-bit address followed by the
Write Bit R/W = 0. If the address matches that of the
LTC3206, the LTC3206 returns an Acknowledge. The
master should then deliver the most significant data byte.
Again the LTC3206 acknowledges and the cycle is re-
peated two more times for a total of one address byte and
three data bytes. Each data byte is transferred to an
internal holding latch upon the return of an Acknowledge.
After all three data bytes have been transferred to the
LTC3206, the master may terminate the communication
with a STOP condition. Alternatively, a REPEAT-START
condition can be initiated by the master and another chip
on the I
2
C bus can be addressed. This cycle can continue
indefinitely and the LTC3206 will remember the last input
of valid data that it received. Once all chips on the bus have
been addressed and sent valid data, a STOP condition can
be sent and the LTC3206 will update its command latch
with the data that it had received.
In certain circumstances, the data on the I
2
C bus may
become corrupted. In these cases the LTC3206 responds
appropriately by preserving only the last set of complete
data that it has received. For example, assume the LTC3206
has been successfully addressed and is receiving data
when a STOP condition mistakenly occurs. The LTC3206
will ignore this stop condition and will not respond until a
new START condition, correct address, new set of data
and STOP condition are transmitted.
Likewise, if the LTC3206 was previously addressed and
sent valid data but not updated with a STOP, it will respond
to any STOP that appears on the bus independent of the
number of REPEAT-STARTs that have occurred. An ex-
ception occurs if a REPEAT-START is given and the
LTC3206 successfully acknowledges its addressed. In
this case, it will not respond to a STOP after the first data
byte is acknowledged. It will, however, respond after the
third data byte is acknowledged.
OPERATIOU
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3215 | 700mA Low Noise High Current LED Charge Pump |
| LTC3215EDD | 700mA Low Noise High Current LED Charge Pump |
| LTC3443 | 700mA Low Noise High Current LED Charge Pump |
| LTC3216EDE | 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control |
| LT3467 | 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3206EUF#PBF | 功能描述:IC LED DRVR WT/RGB BCKLGT 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3206EUF#TR | 功能描述:IC LED DRVR WT/RGB BCKLGT 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3206EUF#TRPBF | 功能描述:IC LED DRVR WT/RGB BCKLGT 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3207 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:600mA Universal Multi-Output LED/CAM Driver |
| LTC3207-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:600mA Universal Multi-Output LED/CAM Driver |
發布緊急采購，3分鐘左右您將得到回復。