- 您現在的位置：買賣IC網 > PDF目錄377774 > LTC3216EDE (LINEAR TECHNOLOGY CORP) 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control PDF資料下載
參數資料
| 型號： | LTC3216EDE |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control |
| 中文描述： | 1.5 A SWITCHED CAPACITOR REGULATOR, PDSO12 |
| 封裝： | 3 X 4 MM, PLASTIC, MO-229-WGED, DFN-12 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 102K |
| 代理商： | LTC3216EDE |
LTC 3216
9
3216fa
from –40
o
C to 85
o
C whereas a Z5U or Y5V style capacitor
will lose considerable capacitance over that range. Z5U
and Y5V capacitors may also have a very poor voltage
coefficient causing them to lose 60% or more of their
capacitance when the rated voltage is applied. Therefore,
when comparing different capacitors, it is often more
appropriate to compare the amount of achievable capaci-
tance for a given case size rather than comparing the
specified capacitance value. For example, over rated volt-
age and temperature conditions, a 1
μ
F, 10V, Y5V ceramic
capacitor in a 0603 case may not provide any more
capacitance than a 0.22
μ
F, 10V, X7R available in the same
case. The capacitor manufacturer’s data sheet should be
consulted to determine what value of capacitor is needed
to ensure minimum capacitances at all temperatures and
voltages.
Table 2 shows a list of ceramic capacitor manufacturers
and how to contact them.
Table 2. Recommended Capacitor Vendors
AVX
Kemet
Murata
Taiyo Yuden
Vishay
TDK
www.avxcorp.com
www.kemet.com
www.murata.com
www.t-yuden.com
www.vishay.com
www.tdk.com
Layout Considerations and Noise
Due to its high switching frequency and the transient
currents produced by the LTC3216, careful board layout is
necessary. A true ground plane and short connections to
all capacitors will improve performance and ensure proper
regulation under all conditions.
The flying capacitor pins C1
+
, C2
+
, C1
–
and C2
–
will have
very high edge rate waveforms. The large dv/dt on these
pins can couple energy capacitively to adjacent PCB runs.
Magnetic fields can also be generated if the flying capaci-
tors are not close to the LTC3216 (i.e., the loop area is
large). To decouple capacitive energy transfer, a Faraday
shield may be used. This is a grounded PCB trace between
the sensitive node and the LTC3216 pins. For a high quality
AC ground, it should be returned to a solid ground plane
that extends all the way to the LTC3216.
Power Efficiency
To calculate the power efficiency (
η
) of a white LED driver
chip, the LED power should be compared to the input
power. The difference between these two numbers repre-
sents lost power whether it is in the charge pump or the
current sources. Stated mathematically, the power effi-
ciency is given by:
η ≡
P
P
LED
IN
(4)
The efficiency of the LTC3216 depends upon the mode in
which it is operating. Recall that the LTC3216 operates as
a pass switch, connecting V
IN
to CPO, until dropout is
detected at the I
LED
pin. This feature provides the optimum
efficiency available for a given input voltage and LED
forward voltage. When it is operating as a switch, the
efficiency is approximated by:
η ≡
=
≈
P
P
V
I
I
IN
V
V
V
LED
IN
LED
LED
IN
LED
IN
·
·
(5)
since the input current will be very close to the LED
current.
At moderate to high output power, the quiescent current
of the LTC3216 is negligible and the expression above is
valid.
Once dropout is detected at the I
LED
pin, the LTC3216
enables the charge pump in 1.5x mode.
In 1.5x boost mode, the efficiency is similar to that of a
linear regulator with an effective input voltage of 1.5 times
the actual input voltage. This is because the input current
for a 1.5x charge pump is approximately 1.5 times the load
current. In an ideal 1.5x charge pump, the power efficiency
would be given by:
η
IDEAL
LED
P
P
IN
LED
V
V
LED
I
I
IN
LED
LED
V
.
15
IN
V
≡
=
≈
·
·15
(6)
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT3467 | 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control |
| LT3467A | 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control |
| LTC3216 | Single Cell 350mA LED Driver |
| LTC3400ES6 | 600mA, 1.2MHz Micropower Synchronous Boost Converter in ThinSOT |
| LTC3400 | 600mA, 1.2MHz Micropower Synchronous Boost Converter in ThinSOT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3216EDE#PBF | 功能描述:IC CHARGE PUMP LED 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC3216EDE#TRPBF | 功能描述:IC CHARGE PUMP LED 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC3217 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:600mA Low Noise Multi-LED Camera Light Charge Pump |
| LTC3217EUD | 制造商:Linear Technology 功能描述:LED DRVR 4Segment 3.3V 16-Pin QFN EP |
| LTC3217EUD#PBF | 功能描述:IC LED DRVR FLASH TORCH 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓撲:開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
發布緊急采購，3分鐘左右您將得到回復。