- 您現在的位置：買賣IC網 > PDF目錄30769 > LTC3534EGN#TR (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 1150 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | LTC3534EGN#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, 1150 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件頁數： | 2/20頁 |
| 文件大?。?/td> | 218K |
| 代理商： | LTC3534EGN#TR |
LTC3534
10
3534f
shifted voltage from the output of the error amplier (VC
pin), see Figure 3. The four power switches are properly
phased so the transfer between operating modes is con-
tinuous, smooth and transparent to the user. When VIN
approaches VOUT the buck-boost region is entered, where
the conduction time of the four switch region is typically
125ns. Referring to Figures 1 and 2, the various regions
of operation will now be described.
Buck Region (VIN > VOUT)
Switch D is always on and switch C is always off dur-
ing this mode. When the internal control voltage, VCI, is
above voltage V1, output A begins to switch. During the
off-time of switch A, synchronous switch B turns on for
the remainder of the period. Switches A and B will alter-
nate similar to a typical synchronous buck regulator. As
the control voltage increases, the duty cycle of switch A
increases until the maximum duty cycle of the converter
in buck mode reaches DMAX_BUCK, given by:
DMAX_BUCK = (100 – D4SW)%
where D4SW = duty cycle % of the four switch range.
D4SW = (125ns f) 100%
where f = operating frequency in Hz, typically 1MHz.
Hence, D4SW = 12.5% for the LTC3534.
DMAX_BUCK = 87.5%
Beyond this point the “four switch”, or buck-boost region
is reached.
Buck-Boost or Four Switch (VIN ~ VOUT)
When the internal control voltage, VCI, is above voltage V2,
switch pair AD remain on for duty cycle DMAX_BUCK, and
the switch pair AC begins to phase in. As switch pair AC
phases in, switch pair BD phases out accordingly. When
VCI reaches the edge of the buck-boost range, at voltage
V3, the AC switch pair completely phase out the BD pair,
and the boost phase begins at duty cycle D4SW.
The input voltage, VIN, where the four switch region begins
is given by:
VIN =
VOUT
1
125ns f
()
V
The VIN potential at which the four switch region ends is
given by:
VIN = VOUT (1 – D) = VOUT (1 – 125ns ) V
where f = operating frequency in Hz, typically 1MHz.
Hence, for the LTC3534,
VIN(ENTER4SW)
VOUT
0.875
V
Approximate VIN potential at which the four switch
region is entered.
VIN(4SWEXIT) 0.875 VOUT V
Approximate VIN potential at which the four switch
region is exited.
Boost Region (VIN < VOUT)
Switch A is always on and switch B is always off during
this mode. When the internal control voltage, VCI
voltage V3, switch pair CD will alternately switch to provide
a boosted output voltage. This operation is typical to a
synchronous boost regulator. The maximum duty cycle
of the converter is limited to 85% typical and is reached
when VCI is above V4.
Burst Mode OPERATION
Burst Mode operation reduces the LTC3534’s quiescent
current consumption at light loads and improves overall
conversion efciency, increasing battery life. During Burst
Mode operation the LTC3534 delivers energy to the output
until it is regulated and then enters a sleep state where
the switches are off and the quiescent current drops to
25μA typical. In this mode the output ripple has a variable
frequency component that depends upon load current,
and will typically be about 2% peak-to-peak. Burst Mode
operation ripple can be reduced slightly by using more
output capacitance (47μF or greater). Another method of
reducing Burst Mode operation ripple is to place a small
feedforward capacitor across the upper resistor in the
VOUT feedback divider network (as in Type III compensa-
tion), see Figure 6.
OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3534EDHC | SWITCHING REGULATOR, 1150 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3536EMSE#PBF | 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO12 |
| LTC3536IMSE#PBF | 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO12 |
| LTC3536EDD#PBF | 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3546EFE#PBF | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3535 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Channel 550mA 1MHz Synchronous Step-Up DC/DC Converter |
| LTC3535EDD#PBF | 功能描述:IC REG BST SYNC ADJ 0.55A 12DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3535EDD#PBF | 制造商:Linear Technology 功能描述:DC/DC CONVERTER IC |
| LTC3535EDD#TRPBF | 功能描述:IC REG BST SYNC ADJ 0.55A 12DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC3535EDD-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Channel 550mA 1MHz Synchronous Step-Up DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。