- 您現在的位置：買賣IC網 > PDF目錄377777 > LTC4052-42 (Linear Integrated Systems) Lithium-Ion Battery Pulse Charger with Overcurrent Protection PDF資料下載
參數資料
| 型號： | LTC4052-42 |
| 廠商： | Linear Integrated Systems |
| 英文描述： | Lithium-Ion Battery Pulse Charger with Overcurrent Protection |
| 中文描述： | 鋰離子電池脈沖充電器與過流保護 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 166K |
| 代理商： | LTC4052-42 |
LTC4052-4.2
7
405242i
Thermal Considerations
The power handling capability is limited by the maximum
rated junction temperature (125
°
C) and the amount of PC
board copper used as a heat sink. The power dissipated by
the device consists of two components:
1. Input supply current multiplied by the input voltage
2. The voltage drop across the switch (SENSE pin to BAT
pin) multiplied by the charge current
The LTC4052 has internal thermal shutdown designed to
protect the IC from overtemperature conditions. For con-
tinuous charging in the fast charge mode, the maximum
junction temperature must not be exceeded. It is important
to give careful consideration to all sources of thermal
resistance from junction to ambient. Additional heat sources
mounted nearby must also be considered.
Surface mount packages rely primarily on the PC board
copper to dissipate the heat generated by the package to the
surrounding air. Since the PC board copper is the heat sink,
generous amounts of copper surrounding the package are
recommended to increase the effectiveness of the heat sink.
In addition, feedthrough vias or plated through holes (lo-
cated directly beneath the package and elsewhere) connect-
ing internal copper and backside copper layers help transfer
and spread the heat generated by the package.
Calculating Junction Temperature
Example: Find the maximum junction temperature for a
battery voltage of 4V (V
IN
will collapse to around V
BAT
in the
fast charge mode), charge current of 1A and a maximum
ambient temperature of 75
°
C.
The power dissipated by the IC is:
P = (I
BAT
I
BAT
R
DS(ON)
) + (V
IN
I
IN
)
= (1A 1A 0.35
) + (4V 1mA)
= 0.35 + 0.004
= 0.354W
The LTC4052 is available in an enhanced 8-pin MSOP
package which features an exposed copper pad on the
bottom of the package allowing it to be soldered directly to
the PC board copper for maximum heat transfer. This
greatly reduces the thermal resistance and increases the
power handling capability when compared to a standard
MSOP package. The junction to aimbient thermal resis-
tance of this package is approximately 35
°
C/W depending
on the copper area. The junction temperature rise above
ambient will be approximately:
(0.354W)(35
°
C/W) = 12.39
°
C
The maximum junction temperature will be equal to the
maximum junction temperature rise above ambient plus
the maximum ambient temperature or:
T
JMAX
= 85
°
C + 12.39
°
C = 97.39
°
C
ACPR Output Pin
When the input voltage is 45mV higher than the voltage at
the BAT pin, the ACPR pin is pulled to ground to indicate
that the input supply (wall adapter) is applied. After the
input supply is removed, this pin will become high imped-
ance. An internal 100ms filter prevents the LTC4052 from
turning off if the voltage at the V
IN
pin rings and gets too
close to V
BAT
due to parasitic inductance.
Stop Charging
The charger is off when the voltage at the V
IN
pin is less
than 45mV above V
BAT
(sleep mode). The charge pump
and the internal pass transistor are turned off, and the
internal resistor divider is disconnected to reduce the
current drain on the battery in the sleep mode.
APPLICATIU
W
U
U
GATE
VOLTAGE
V
IN
4052 TA02
10
μ
A/C
10
μ
A/C
50
μ
A/C
50
μ
A/C
50
μ
A/C
10
μ
A/C
Figure 2. Slew Rate at GATE and V
IN
Pins
with the RC Network from GATE to V
IN
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4052EMS8E-4.2 | Lithium-Ion Battery Pulse Charger with Overcurrent Protection |
| LTC4056 | 150mA Standalone Linear Li-Ion Battery Charger in ThinSOT |
| LTC1732-4.2 | Lithium-Ion Linear Battery Charger Controller |
| LTC1731EMS8-4.1 | Lithium-Ion Linear Battery Charger Controller |
| LTC1731ES8-4.1 | Lithium-Ion Linear Battery Charger Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4052EMS8E-4.2 | 功能描述:IC CHARGER PULSE LI-ION 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4052EMS8E-4.2#PBF | 功能描述:IC CHARGER PULSE LI-ION 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4052EMS8E-4.2#TR | 功能描述:IC CHARGER PULSE LI-ION 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4052EMS8E-4.2#TRPBF | 功能描述:IC CHARGER PULSE LI-ION 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4053 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:150mA Standalone Linear Li-Ion Battery Charger in ThinSOT |
發布緊急采購，3分鐘左右您將得到回復。