- 您現在的位置：買賣IC網 > PDF目錄30772 > LTC4217CFE#TR (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 PDF資料下載
參數資料
| 型號： | LTC4217CFE#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 |
| 封裝： | 4.40 MM, PLASTIC, SSOP-20 |
| 文件頁數： | 6/18頁 |
| 文件大小： | 238K |
| 代理商： | LTC4217CFE#TR |
LTC4217
14
4217fe
applicaTions inForMaTion
invoked by tying the TIMER pin to INTVCC. After the 2ms
timeout the FLT pin needs to pull-down on the UV pin to
restart the power-up sequence.
Since the default values for overvoltage, undervoltage and
power good thresholds for the 12V fixed version match
the requirements, no external components are required
for the UV, OV and FB pins.
The final schematic in Figure 6 results in very few external
components. The pull-up resistor, R1, connects to the
PG pin while the 20k (R2) converts the IMON current to a
voltage at a ratio:
VIMON = 50[A/A] 20k IOUT = 1[V/A] IOUT
In addition there is a 0.1F bypass (C1) on the INTVCC pin.
Layout Considerations
In Hot Swap applications where load currents can be 2A,
narrowPCBtracksexhibitmoreresistancethanwidertracks
and operate at elevated temperatures. The minimum trace
width for 1oz copper foil is 0.02" per amp to make sure
the trace stays at a reasonable temperature. Using 0.03"
per amp or wider is recommended. Note that 1oz copper
exhibits a sheet resistance of about 0.5mΩ/square. Small
resistances add up quickly in high current applications.
There are two VDD pins on opposite sides of the package
that connect to the sense resistor and MOSFET. The PCB
layout should be balanced and symmetrical to each VDD
pin to balance current in the MOSFET bond wires. Figure 7
shows a recommended layout for the LTC4217.
Although the MOSFET is self protected from overtem-
perature, it is recommended to solder the backside of the
package to a copper trace to provide a good heat sink. Note
that the backside is connected to the SENSE pin and can-
not be soldered to the ground plane. During normal loads
the power dissipated in the MOSFET is as high as 0.23W.
A 10mm × 10mm area of 1oz copper should be sufficient.
This area of copper can be divided in many layers.
It is also important to put C1, the bypass capacitor for
the INTVCC pin as close as possible between the INTVCC
and GND.
Additional Applications
TheLTC4217hasawideoperatingrangefrom2.9Vto26.5V.
The UV, OV and PG thresholds are set with few resistors.
All other functions are independent of supply voltage.
Figure 8 shows a 3.3V application with a UV threshold of
2.87V, an OV threshold of 3.77V and a PG threshold of
3.05V. The last page includes a 24V application with a UV
threshold of 19.9V, an OV threshold of 26.3V and a PG
threshold of 20.75V.
Figure 8. 3.3V, 1.5A Card Resident Application
R4
14.7k
R5
10k
R1
17.4k
ADC
R2
3.16k
CT
0.1F
R3
10k
3.3V
RMON
20k
4217 F08
R6
10k
CL
100F
VDD
UV
OUT
FB
PG
GND
IMON
LTC4217FE
OV
INTVCC
TIMER
FLT
+
VOUT
3.3V
1.5A
4217 F07
HEAT SINK
VIA TO
SINK
GND
C
OUT
VDD
Figure 7. Recommended Layout
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4217IDHC#PBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC4219IDHC-5#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4219IDHC-12#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4219IDHC-5#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4219CDHC-5#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4217CFE-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2A Integrated Hot Swap Controller |
| LTC4217HFE#PBF | 功能描述:IC CTRLR HOT SWAP 2A 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4217HFE#TRPBF | 功能描述:IC CTRLR HOT SWAP 2A 20-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4217IDHC | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2A Integrated Hot Swap Controller |
| LTC4217IDHC#PBF | 功能描述:IC CTRLR HOT SWAP 2A 16-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。