- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4232CDHC#TRPBF (Linear Technology)IC CTLR HOT SWAP 5A 16-DFN Datasheet資料下載
參數資料
| 型號： | LTC4232CDHC#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 242K |
| 描述： | IC CTLR HOT SWAP 5A 16-DFN |
| 標準包裝： | 2,500 |
| 類型： | 熱交換開關 |
| 應用： | 服務器，儲存，通信，嵌入式，消費品 |
| 內部開關： | 是 |
| 電流限制： | 可調 |
| 電源電壓： | 2.9 V ~ 15 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 16-DFN（5x3） |
| 包裝： | 帶卷 (TR) |
LTC4232
6
4232fa
pin FuncTions
FB: Foldback and Power Good Input. Connect this pin to
an external resistive divider from OUT. If the voltage falls
below 0.6V, the current limit is reduced using a foldback
profile (see the Typical Performance Characteristics sec-
tion). If the voltage falls below 1.21V, the PG pin will pull
low to indicate the power is bad.
FLT: Overcurrent Fault Indicator. Open-drain output pulls
low when an overcurrent fault has occurred and the circuit
breaker trips. For overcurrent auto-retry tie to UV pin (see
the Applications Information section for details).
GATE: Gate Drive for Internal N-channel MOSFET. An
internal 24礎 current source charges the gate of the
N-channel MOSFET. At start-up the GATE pin ramps up at
a 0.3V/ms rate determined by internal circuitry. During an
undervoltage or overvoltage condition a 250礎 pull-down
current turns the MOSFET off. During a short-circuit or
undervoltage lockout condition, a 140mA pull-down cur-
rent source between GATE and OUT is activated.
GND: Device Ground.
I
MON
: Current Monitor Output. The current in the internal
MOSFET switch is divided by 50,000 and sourced from this
pin. Placing a 20k resistor from this pin to GND creates a
0V to 2V voltage swing when current ranges from 0A to 5A.
INTV
CC
: Internal 3.1V Supply Decoupling Output. This pin
must have a 0.1礔 or larger bypass capacitor.
I
SET
: Current Limit Adjustment Pin. For a 5.6A current limit
value open this pin. This pin is driven by a 20k resistor in
series with a voltage source. The pin voltage is used to
generate the current limit threshold. The internal 20k resis-
tor and an external resistor between I
SET
and ground create
an attenuator that lowers the current limit value. In order
to match the temperature variation of the sense resistor,
the voltage on this pin increases at the same rate as the
sense resistance increases. Therefore the voltage at I
SET
pin is proportional to temperature of the MOSFET switch.
OUT: Output of Internal MOSFET Switch. Connect this pin
directly to the load.
OV: Overvoltage Comparator Input. Connect this pin to an
external resistive divider from V
DD
. If the voltage at this
pin rises above 1.235V, an overvoltage is detected and
the switch turns off. Tie to GND if unused.
PG: Power Good Indicator. Open-drain output pulls low
when the FB pin drops below 1.21V indicating the power is
bad. If the FB pin rises above 1.23V and the GATE to OUT
voltage exceeds 4.2V, the open-drain pull-down releases
the PG pin to go high.
SENSE: Current Sense Node and MOSFET Drain. The cur-
rent limit circuit controls the GATE pin to limit the sense
voltage between the V
DD
and SENSE pins to 42mV (5.6A)
or less depending on the voltage at the FB pin. The exposed
pad on DHC packages are connected to SENSE and must
be soldered to an electrically isolated printed circuit board
trace to properly transfer the heat out of the package.
TIMER: Timer Input. Connect a capacitor between this pin
and ground to set a 12ms/礔 duration for current limit
before the switch is turned off. If the UV pin is toggled
low while the MOSFET switch is off, the switch will turn
on again following a cooldown time of 518ms/礔 duration.
Tie this pin to INTV
CC
for a fixed 2ms overcurrent delay
and 100ms auto-retry time.
UV: Undrvoltage Comparator Input. Tie high if unused.
Connect this pin to an external resistive divider from V
DD
.
If the UV pin voltage falls below 1.15V, an undervoltage is
detected and the switch turns off. Pulling this pin below
0.62V resets the overcurrent fault and allows the switch
to turn back on (see the Applications Information section
for details). If overcurrent auto-retry is desired then tie
this pin to the FLT pin.
V
DD
: Supply Voltage and Current Sense Input. This pin
has an undervoltage lockout threshold of 2.73V.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4240IGN#TRPBF | IC CTRLR HOTSWAP CPCI I2C 28SSOP |
| LTC4241IGN#PBF | IC CTRLR HOTSWAP 3.3V AUX 20SSOP |
| LTC4242CUHF#TRPBF | IC CNTRLR HOT SWAP 38-QFN |
| LTC4244CGN-1#TRPBF | IC CTRLR HOTSWAP PCI 20-SSOP |
| LTC4245CG#TRPBF | IC CNTRLR HOT SWAP 36-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4232IDHC#PBF | 功能描述:IC CTLR HOT SWAP 5A 16-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4232IDHC#TRPBF | 功能描述:IC CTLR HOT SWAP 5A 16-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4240 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:CompactPCI Hot Swap Controller with I2C Compatible Interface |
| LTC4240CGN | 功能描述:IC CTRLR HOTSWAP CPCI I2C 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4240CGN#PBF | 功能描述:IC CTLR HOT SWAP CPCI I2C 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。