參數資料
型號： LTC4240IGN
廠商： LINEAR TECHNOLOGY CORP
元件分類： 電源管理
英文描述： CompactPCI Hot Swap Controller with I2C Compatible Interface
中文描述： 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO28
封裝： 0.150 INCH, PLASTIC, SSOP28
文件頁數： 8/28頁
文件大?。?/td> 486K
代理商： LTC4240IGN
LTC4240
8
4240f
PWRGD (Pin 8):
Open-Drain Power Good Output. Con-
nect the CPCI HEALTHY# signal to the PWRGD pin.
PWRGD remains low while V
12VOUT
≥
11.1V, V
3VOUT
≥
2.9V, V
5VOUT
≥
4.65V and V
EEOUT
≤
–10.5V. When any of
the supplies drops below its power good threshold volt-
age, PWRGD will go high after a 10
μ
s deglitching time. The
switches will not be turned off when PWRGD goes high,
unless a fault has occurred. The CPCI specification calls
for a 0.01
μ
F bypass capacitor on the backplane for
HEALTHY#.
BE (Pin 9):
QuickSwitch Bus Enable Output. The BE output
remains high until power is good on all supplies. This
serves to isolate the I/O data lines during live
insertion. This is a CMOS output powered by 5V
IN
.
GND (Pin 10):
Analog Ground. Connect to analog ground
plane.
ADDRIN (Pin 11):
I
2
C Address Programming Input. The
I
2
C address is programmed by connecting the ADDRIN
pin to a resistor divider between the 5V
IN
pin and GND. See
Table 1 for 1% resistor values and corresponding ad-
dresses. Resistors must be placed close to the ADDRIN
pin to minimize errors due to stray capacitance and
resistance on the board trace. Connect this pin to ground
if I
2
C is not used.
SDA (Pin 12):
I
2
C Data Input and Output. Note that TTL
levels are used. Connect this pin to ground if I
2
C is not
used.
SCL (Pin 13):
I
2
C Clock Input, 100kHz Maximum. Note
that TTL levels are used. Do not float. Connect this pin to
ground if I
2
C is not used.
RESETOUT (Pin 14):
Open-Drain Reset Output. Connect
the CPCI LOCAL_PCI_RST# signal to the RESETOUT pin.
RESETOUT is the logical combination of RESETIN, PWRGD,
and I
2
C RESETOUT latch output.
LED (Pin 15):
CPCI Status LED. Pulls low to light LED
when RESETOUT is low or when the I
2
C LED latch is set.
DGND (Pin 16):
Digital Ground. Connect to ground plane.
DRIVE (Pin 17):
External transistor’s base drive output for
bus precharge. Connects to the base of an external NPN
emitter-follower which in turn biases the PRECHARGE
PRSNT1# (Pin 1):
PCI Present Detect Input 1. PRSNT1#
and PRSNT2# are readable over the I
2
C Bus. PRSNT1#
and PRSNT2# indicate the maximum power used by the
card. Do not float.
PRSNT2# (Pin 2):
PCI Present Detect Input 2. Do not float.
12V
IN
(Pin 3):
12V Supply Input. A 0.5
switch is inter-
nally connected between 12V
IN
and 12V
OUT
with foldback
current limit. An undervoltage lockout circuit prevents the
switches from turning on while the 12V
IN
pin is below 8V.
12V
IN
provides power to some of the LTC4240’s internal
circuitry. See Input Transient Protection section on how to
protect 12V
IN
from large voltage transients.
V
EEIN
(Pin 4):
–12V Supply Input. A 1
internal switch is
connected between V
EEIN
and V
EEOUT
with foldback cur-
rent limit. An undervoltage lockout circuit prevents the
switches from turning on while V
EEIN
is above –9V. See
Connecting V
EEIN
section for more notes on V
EEIN
and
V
EEOUT
. Also refer to Input Transient Protection section.
TIMER/AUX 12V
IN
(Pin 5):
Current Fault Inhibit Timing
Input. Connect a capacitor from TIMER to GND. With the
LTC4240 turned off (OFF/ON = HIGH), the TIMER pin is
internally held at GND. When the device is turned on, an
11.5
μ
A pull-up current source is connected to TIMER.
Current limit faults will be ignored until the voltage at the
TIMER pin rises above 5.5V. The Timer capacitor also
serves as an auxiliary charge reservoir for internal V
CC
in
the event the 12V
IN
pin voltage glitches below the LTC4240
UVL threshold voltage.
5V
OUT
(Pin 6):
5V Output Sense. The PWRGD pin will not
pull low until the 5V
OUT
pin voltage exceeds 4.65V. When
the power switches are turned off, a 50
resistor pulls
5V
OUT
to ground.
FAULT (Pin 7):
Open-Drain Fault Output . FAULT is pulled
low when a current limit fault is detected. Current limit
faults are ignored until the voltage at the TIMER pin is
above 5.5V. Once the TIMER cycle is complete, FAULT
pulls low and the LTC4240 turns off (in the event of an
overcurrent fault lasting longer than 35
μ
s). The LTC4240
will remain in the off state until the OFF/ON pin is cycled
high then low or power is cycled. Note that the OFF/ON
cycling can also be performed using I
2
C bus.
PIU
相關PDF資料
PDF描述
LTC4240CGN CompactPCI Hot Swap Controller with I2C Compatible Interface
LTC4244 Rugged, CompactPCI Bus Hot Swap Controllers
LTC4244CGN-1 Rugged, CompactPCI Bus Hot Swap Controllers
LTC4244IGN Rugged, CompactPCI Bus Hot Swap Controllers
LTC4244IGN-1 Rugged, CompactPCI Bus Hot Swap Controllers
相關代理商/技術參數
參數描述
LTC4240IGN#PBF 功能描述:IC CTRLR HOTSWAP CPCI I2C 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4240IGN#TR 功能描述:IC CTRLR HOT SWAP CPCI 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4240IGN#TRPBF 功能描述:IC CTRLR HOTSWAP CPCI I2C 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4241 制造商:LINER 制造商全稱:Linear Technology 功能描述:PCI-Bus with 3.3V Auxiliary Hot Swap Controller
LTC4241CGN 功能描述:IC CTRLR HOTSWAP PCI 3.3V 20SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*