參數資料
型號： LTC4259ACGW#PBF
廠商： Linear Technology
文件頁數： 10/32頁
文件大小： 0K
描述： IC CTRLR POE QUAD AC DISC 36SSOP
產品培訓模塊： Power over Ethernet
標準包裝： 32
控制器類型： 以太網供電控制器（POE）
接口： I²C
電源電壓： 3 V ~ 4 V
電流 - 電源： 2.5mA
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 36-BSOP（0.295"，7.50mm 寬）
供應商設備封裝： 36-SSOP
包裝： 管件
產品目錄頁面： 1338 (CN2011-ZH PDF)
LTC4259A
18
4259afb
Dual-Level Current Limit
A PD is permitted to draw up to 15.4W continuously and
up to 400mA for 50ms. The LTC4259A has two correspond-
ing current limit thresholds, ICUT (375mA typ) and ILIM
(425mA typ). These are given by the equations:
ICUT = VCUT/RS, ILIM = VLIM/RS
RS is the sense resistor and should be 0.5 for IEEE
802.3af compliance. While the LTC4259A allows the port
current to exceed ICUT for a limited time period (see tICUT
timing below), it does not allow the current to exceed ILIM.
The current limit circuit monitors the port current by
monitoring the voltage across the sense resistor and re-
duces the MOSFET gate voltage as needed to keep the
current at or below ILIM. When the current drops below
ILIM, the gate voltage is restored to the full value to keep
the MOSFET resistance to a minimum.
tICUT Timing
Whenever more than ICUT = VCUT/RS flows through a port,
the port’s sense voltage is above VCUT and the tICUT timer
counts up. The tICUT timer also counts up when the port’s
OUT pin voltage is above VPG. If either of these conditions
persists and the tICUT timer expires, the LTC4259A will turn
off power to the port immediately and set the appropriate
tICUT fault bit in register 06h/07h. The tICUT duration can be
programmed via register 16h, bits 2 and 3 (Table 1).
The tICUT timer is an up/down counter that is designed to
protect the external MOSFET from thermal stress caused
by repeatedly operating in current limit. The counter
counts up whenever the current is above ICUT and counts
down at 1/16th the rate when it is not. The counter will
bottom out at zero to prevent underflow. Full count indi-
cates that the tICUT timer has expired and the port will be
turned off.
This count up/count down behavior implements duty cycle
protection, preventing intermittent current limit faults from
causing cumulative thermal stress in the MOSFET. If the port
enters current limit but then exits before the timer expires,
the count will decrease slowly, giving the ICUT timer the
ability to turn off sooner in the case of a repetitive fault. If
the overcurrent duty cycle is less than 6.3% the tICUT timer
will be fully reset.
If the tICUT timer expires and causes the port to shut off, the
timer will continue to run, counting down at the slow
1/16th rate and preventing the port from being repowered
until the count returns to zero. This protects the MOSFET
from damage due to a faulty PD that may still have a valid
signature, or from errant software that repeatedly writes to
the Power On bit.
The port will not repower until after the tICUT counter
returns to zero. In manual and semiauto modes the power
enable command must be received after the tICUT counter
reaches zero. In auto mode the LTC4259A must complete
a valid detection cycle after the tICUT counter reaches zero.
tSTART Timing
To distinguish between normal turn-on current limit be-
havior and current limit faults which occur after power-up
is complete, the LTC4259A starts a timer (the tSTART timer)
whenever a power-up sequence begins.
The tSTART timer serves three functions. First and fore-
most, it allows the user to specify a different current limit
timeout (tSTART instead of tICUT) during turn-on (current
limit duty cycle protection remains functional). Second,
the DC disconnect timer is disabled during this period and
can only begin counting up after the tSTART timer has
expired. Together, these two features let the PD draw the
maximum current IINRUSH to charge its input capacitance,
boot up and begin drawing power without triggering a
tSTART fault. Finally, if the device is in current limit for the
entire tSTART period, a tSTART fault will be generated
instead of a tICUT fault. This can be useful for tracking down
the cause of an overcurrent fault.
As long as the PD draws less than ICUT at the end of tSTART
and begins drawing the minimum current within tDIS after
tSTART expires (if DC disconnect is enabled), no faults will
be indicated.
The tSTART timer also implements the duty cycle protec-
tion described under tICUT timing and its duration can be
programmed via register 16h, bits 5 and 4 (Table 1).
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料
PDF描述
VNC2-64Q1B-REEL IC USB HOST/DEVICE CTRL 64-QFN
V72A48C400BF2 CONVERTER MOD DC/DC 48V 400W
PIC16F1827-E/SO MCU PIC 8BIT 4K FLASH 18-SOIC
PIC16F1826T-I/MV MCU PIC 8BIT 2K FLASH 28-UQFN
PIC16F1826T-I/ML MCU PIC 8BIT 2K FLASH 28-QFN
相關代理商/技術參數
參數描述
LTC4259AIGW-1 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect
LTC4259AIGW-1#PBF 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4259AIGW-1#TRPBF 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4259CGW-ES 制造商:LINEAR_TECH 功能描述:
LTC4260 制造商:LINER 制造商全稱:Linear Technology 功能描述:UV, OV and Reverse Supply Protection Controller Low Operating Current: 125μA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*