- 您現在的位置：買賣IC網 > PDF目錄1935 > LTC4259ACGW#TR (Linear Technology)IC CTRLR POE QUAD AC DISC 36SSOP PDF資料下載
參數資料
| 型號： | LTC4259ACGW#TR |
| 廠商： | Linear Technology |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTRLR POE QUAD AC DISC 36SSOP |
| 標準包裝： | 1,000 |
| 控制器類型： | 以太網供電控制器（POE） |
| 接口： | I²C |
| 電源電壓： | 3 V ~ 4 V |
| 電流 - 電源： | 2.5mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-BSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4259A
13
4259afb
involves reading the register to determine its status, set-
ting the appropriate bit in software and writing back the
entire register, a pushbutton register allows a single bit to
be written without knowing or affecting the status of the
other bits in the register. Pushbutton registers are write-
only and will return 00h if read.
Det/Class Restart PB (Address 18h): Detection/Classifi-
cation Restart Pushbutton Register, Write Only. Writing a
1 to any bit in this register will start or restart a single
detection or classification cycle at the corresponding port
in Manual mode. It can also be used to set the correspond-
ing bits in the Detect/Class Enable register (address 14h)
for ports in auto or semiauto mode. The lower 4 bits affect
detection on each port while the upper 4 bits affect
classification.
Power Enable PB (Address 19h): Power Enable Pushbutton
Register, Write Only. The lower four bits of this register set
the Power Enable bit in the corresponding Port Status reg-
ister; the upper four bits clear the corresponding Power
Enable bit. Setting or clearing the Power Enable bits via this
register will turn on or off the power in any mode except
shutdown, regardless of the state of detection or classifi-
cation. Note that tICUT, tSTART and disconnect events (if
enabled) will still turn off power if they occur.
The Power Enable bit cannot be set if the port has turned
off due to a tICUT or tSTART fault and the tICUT timer has not
yet counted back to zero. See Applications Information for
more information on tICUT timing.
Clearing the Power Enable bits with this register also
clears the detect and fault event bits, the Port Status
register, and the Detection and Classification Enable bits
for the affected port(s).
Reset PB (Address 1Ah): Reset Pushbutton, Write Only.
Bits 0-3 reset the corresponding port by clearing the power
enable bit, the detect and fault event bits, the status regis-
ter and the detection and classification enable bits for that
port. Bit 4 returns the entire LTC4259A to the power-on
reset state; all ports are turned off, the AUTO pin is reread
and all registers are returned to their power-on defaults,
except VDDUVLO, which remains cleared. Bit 5 is reserved;
setting it has no effect. Setting bit 6 releases the Interrupt
pin if it is asserted without affecting the Event registers or
the Interrupt register. When the INT pin is released in this
Detect/Class Enable (Address 14h): Detection and Clas-
sification Enable, Read/Write. The lower four bits of this reg-
ister enable the detection circuitry at the corresponding port
if that port is in Auto or Semiauto mode. The upper four bits
enable the classification circuitry at the corresponding port
if that port is in Auto or Semiauto mode. In manual mode,
setting a bit in this register will cause the LTC4259A to per-
form one classification or detection cycle on the corre-
sponding port. Writing to the Detect/Class Restart PB (18h)
has the same effect without disturbing the Detect/Class
Enable bits for other ports.
Timing Config (Address 16h):Global Timing Configuration,
Read/Write. Bits 0-1 program tDIS, the time duration before
a port is automatically tuned off after the PD is removed.
The LTC4259A can be programmed to monitor whether port
current is below IMIN (DCconnect)orportimpedanceishigh
(AC disconnect). Bits 2-3 program tICUT, the time during
which a port’s current can exceed ICUT without it being
turned off. If the current is still above ICUT after tICUT, the
LTC4259A will indicate a tICUT fault and turn the port off.
Bits 4-5 program tSTART, the time duration before an over-
current condition during port power-on is considered a
tSTART fault and the port is turned off. Note that using the
tICUT and tSTART times other than the default is not compli-
ant with IEEE 802.3af and may double or quadruple the
energy dissipated by the external MOSFETs during fault con-
ditions. Bits 6-7 are reserved and should be read/written
as 0. See Electrical Characteristics for timer bit encoding.
Also see the Applications Information for descriptions of
tSTART, tICUT, DC and AC disconnect timing.
Misc Config (Address 17h): Miscellaneous Configuration,
Read/Write. Bit 5 is the Osc Fail Mask; it is set by default.
When the Osc Fail Mask bit is clear, it prevents a failure on
the OSCIN pin from setting the Osc Fail bit and causing a
Supply Event Interrupt. Setting bit 7 enables the INT pin.
If this bit is reset, the LTC4259A will not pull down the INT
pin in any condition nor will it respond to the Alert Response
Address. This bit is set by default.
Pushbutton Registers
Note Regarding Pushbutton Registers: “Pushbutton” reg-
isters are specialized registers that trigger an event when
a 1 is written to a bit; writing a 0 to a bit will do nothing. Unlike
a standard read/write register, where setting a single bit
REGISTER FU CTIO S
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4264IDE#TRPBF | IC CNTRLR PD INTERFACE 12-DFN |
| LTC4266IGW#PBF | IC CTRLR IEEE 802.3AT 36-SSOP |
| LTC4267IDHC#TRPBF | IC POE 802.3AF INTERFACE 16-DFN |
| LTC4278IDKD#TRPBF | IC PD IEEE 802.3AT 25.5W 32-DFN |
| LTC4305IDHD#TRPBF | IC BUFFER BUS 2WR ADDRESS 16-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4259AIGW-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect |
| LTC4259AIGW-1#PBF | 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4259AIGW-1#TRPBF | 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4259CGW-ES | 制造商:LINEAR_TECH 功能描述: |
| LTC4260 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:UV, OV and Reverse Supply Protection Controller Low Operating Current: 125μA |
發布緊急采購，3分鐘左右您將得到回復。