- 您現在的位置：買賣IC網 > PDF目錄377778 > LTC4260 (Linear Technology Corporation) Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring PDF資料下載
參數資料
| 型號： | LTC4260 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
| 中文描述： | 正高電壓熱插拔控制器帶有I2C兼容監(jiān)測 |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 266K |
| 代理商： | LTC4260 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC4260
8
4260f
GPIO:
General Purpose Input/Output. Open-drain logic
output and logic input. Defaults to pull low to indicate
power is bad. Configure according to Table 3.
NC:
No Connect. Unconnected pins. These pins provide
extra distance between high and low voltage pins.
ON:
On Control Input. A rising edge turns on the external
N-channel FET and a falling edge turns it off. This pin is
also used to configure the state of the FET ON bit (and
hence the external FET) at power up. For example if the ON
pin is tied high, then the FET ON control bit (A3) will go high
100ms after power-up. Likewise if the ON pin is tied low
then the part will remain off after power-up until the FET
ON control bit is set high using the I
2
C bus. A high-to-low
transition on this pin will clear faults.
OV (GN/UH Packages):
Overvoltage Comparator Input.
Connect this pin to an external resistive divider from V
DD
.
If the voltage at this pin rises above 3.5V, an overvoltage
fault is detected and the switch turns off. Tie to GND if
unused.
SCL:
Serial Bus Clock Input. Data at the SDA pin is shifted
in or out on rising edges of SCL. This is a high impedance
pin that is generally driven by an open-collector output
from a master controller. An external pull-up resistor or
current source is required.
SDAI:
Serial Bus Data Input. A high impedance input used
for shifting in address, command or data bits. Normally
tied to SDAO to form the SDA line.
SDAO:
Serial Bus Data Output. Open-drain output used for
sending data back to the master controller or acknowledg-
ing a write operation. Normally tied to SDAI to form the
SDA line. An external pull-up resistor or current source is
required.
SENSE:
Current Sense Input. Connect this pin to the
output of the current sense resistor. The current limit
circuit controls the GATE pin to limit the sense voltage
between the V
DD
and SENSE pins to 50mV or less depend-
ing on the voltage at the FB pin. This pin is used as an input
to the 8-bit ADC.
SOURCE:
N-Channel MOSFET Source Connection and
ADC Input. Connect this pin to the source of the external
N-channel MOSFET switch. This pin also serves as the
ADC input to monitor output voltage. The pin provides a
return for the gate pull-down circuit and as a supply for the
charge pump circuit.
TIMER:
Timer Input. Connect a capacitor between this
pin and ground to set a 12ms/
μ
F duration for current limit
before the switch is turned off. The duration of the off
time is 518ms/
μ
F when autoretry during current limit is
enabled. A minimum value of 0.1nF must be connected
to this pin.
UV:
Undervoltage Comparator Input. Connect this pin to
an external resistive divider from V
DD
. If the voltage at this
pin falls below 3.12V, an undervoltage fault is detected and
the switch turns off. Pulling this pin below 1.2V resets all
faults and allows the switch to turn back on. Tie to INTV
CC
if unused.
V
DD
:
Supply Voltage and Current Sense Input. This pin has
an undervoltage lockout threshold of 7.45V.
INTV
CC
:
Internal Low Voltage Supply Decoupling Output.
Connect a 0.1
μ
F capacitor from this pin to ground. This pin
can be used to drive the other pins to logic high and has an
undervoltage lockout threshold of 3.8V.
V
DDK
(UH Package):
Same as V
DD
. Connect this pin to
V
DD
. V
DDK
tied to V
DD
internally with 18
.
PIU
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4260CGN | Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
| LTC4260CSW | Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
| LTC4260CUH | Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
| LTC4260IGN | Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
| LTC4260ISW | Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4260CGN | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 80V 24-Pin SSOP N |
| LTC4260CGN#PBF | 功能描述:IC CTLR HOT SWAP I2C 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4260CGN#TR | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 80V 24-Pin SSOP N T/R |
| LTC4260CGN#TRPBF | 功能描述:IC HOT SWAP CNTRL I2C 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4260CSW | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
發(fā)布緊急采購，3分鐘左右您將得到回復。