參數資料
型號： LTC4267IGN#TRPBF
廠商： Linear Technology
文件頁數： 15/32頁
文件大?。?/td> 0K
描述： IC POE 802.3AF INTERFACE 16SSOP
標準包裝： 2,500
控制器類型： 以太網供電控制器（POE）
接口： IEEE 802.3af
電流 - 電源： 3mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 16-SSOP
包裝： 帶卷 (TR)
相關產品： 732-2437-6-ND - TRANS FLYBACK POE 40UH SMD
732-2436-6-ND - TRANS FLYBACK POE 35UH SMD
732-2435-6-ND - TRANS FLYBACK POE 127UH SMD
732-2434-6-ND - TRANS FLYBACK POE 127UH SMD
732-2433-6-ND - TRANS FLYBACK POE 127UH SMD
732-2432-6-ND - TRANS FLYBACK POE 127UH SMD
732-2431-6-ND - TRANS FLYBACK POE 127UH SMD
732-2430-6-ND - TRANS FLYBACK POE 127UH SMD
732-2437-1-ND - TRANS FLYBACK POE 40UH SMD
732-2436-1-ND - TRANS FLYBACK POE 35UH SMD
更多...
LTC4267
22
4267fc
APPLICATIO S I FOR ATIO
WU
UU
Programmable Slope Compensation
The LTC4267 switching regulator injects a ramping current
through its SENSE pin into an external slope compensation
resistor (RSL in Figure 11). This current ramp starts at
zero after the NGATE pin has been high for the LTC4267’s
minimum duty cycle of 6%. The current rises linearly to-
wards a peak of 5A at the maximum duty cycle of 80%,
shutting off once the NGATE pin goes low. A series resis-
tor (RSL) connecting the SENSE pin to the current sense
resistor (RSENSE) develops a ramping voltage drop. From
the perspective of the LTC4267 SENSE pin, this ramping
voltage adds to the voltage across the sense resistor,
effectively reducing the current comparator threshold in
proportion to duty cycle. This stabilizes the control loop
against subharmonic oscillation. The amount of reduction
in the current comparator threshold (VSENSE) can be
calculated using the following equation:
VSENSE = 5A RSL [(Duty Cycle – 6%)/74%]
Note: The LTC4267 enforces 6% < Duty Cycle < 80%.
Designs not needing slope compensation may replace RSL
with a short-circuit.
Applications Employing a Third Transformer Winding
A standard operating topology may employ a third
winding on the transformer’s primary side that provides
power to the LTC4267 switching regulator via its PVCC pin
(Figure 11). However, this arrangement is not inherently
self-starting. Start-up is usually implemented by the use of
an external “trickle-charge” resistor (RSTART) in conjunc-
tion with the internal wide hysteresis undervoltage lockout
circuit that monitors the PVCC pin voltage.
RSTART is connected to VPORTP and supplies a current,
typically 100A, to charge CPVCC. After some time, the
voltage on CPVCC reaches the PVCC turn-on threshold. The
LTC4267 switching regulator then turns on abruptly and
draws its normal supply current. The NGATE pin begins
switching and the external MOSFET (Q1) begins to deliver
power. The voltage on CPVCC begins to decline as the
switching regulator draws its normal supply current, which
exceeds the delivery from RSTART.Aftersometime,typically
tens of milliseconds, the output voltage approaches the
desired value. By this time, the third transformer winding
is providing virtually all the supply current required by the
LTC4267 switching regulator.
One potential design pitfall is under-sizing the value of
capacitor CPVCC. In this case, the normal supply current
drawn through PVCC will discharge CPVCC rapidly before the
third winding drive becomes effective. Depending on the
particular situation, this may result in either several off-on
cycles before proper operation is reached or permanent
relaxation oscillation at the PVCC node.
Resistor RSTART should be selected to yield a worst-case
minimum charging current greater that the maximum rated
LTC4267 start-up current to ensure there is enough current
to charge CPVCC to the PVCC turn-on threshold. RSTART
should also be selected large enough to yield a worst-case
maximum charging current less than the minimum-rated
PVCC supply current, so that in operation, most of the
PVCC current is delivered through the third winding. This
results in the highest possible efciency.
Capacitor CPVCCshouldthenbemadelargeenoughtoavoid
the relaxation oscillation behavior described previously.
This is difcult to determine theoretically as it depends on
the particulars of the secondary circuit and load behavior.
Empirical testing is recommended.
The third transformer winding should be designed so
that its output voltage, after accounting for the forward
diode voltage drop, exceeds the maximum PVCC turn-off
threshold. Also, the third winding’s nominal output voltage
should be at least 0.5V below the minimum rated PVCC
clamp voltage to avoid running up against the LTC4267
shunt regulator, needlessly wasting power.
PVCC Shunt Regulator
In applications including a third transformer winding,
the internal PVCC shunt regulator serves to protect the
LTC4267 switching regulator from overvoltage transients
as the third winding is powering up.
If a third transformer winding is undesirable or unavail-
able, the shunt regulator allows the LTC4267 switching
regulator to be powered through a single dropping resistor
from VPORTP as shown in Figure 12. This simplicity comes
at the expense of reduced efciency due to static power
dissipation in the RSTART dropping resistor.
相關PDF資料
PDF描述
LTC4267CGN#PBF IC POE 802.3AF INTERFACE 16SSOP
LTC4267CDHC#TRPBF IC POE 802.3AF INTERFACE 16-DFN
LTC4267CGN#TRPBF IC POE 802.3AF INTERFACE 16SSOP
031-4237 CONN BNC RCPT BULKHEAD REAR MNT
VI-2NJ-CV-S CONVERTER MOD DC/DC 36V 150W
相關代理商/技術參數
參數描述
LTC4268-1 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad IEEE 802.3at Power over Ethernet Controller
LTC4268-1_12 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power PD With Synchronous No-Opto Flyback Controller
LTC4268CDKD-1 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power PD with Synchronous NoOpto Flyback Controller
LTC4268CDKD-1#PBF 功能描述:IC PD HIGH POWER W/CNTRL 32-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4268CDKD-1#TRPBF 功能描述:IC PD HIGH POWER W/CNTRL 32-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*