參數資料
型號: LTC4312IDE#PBF
廠商: Linear Technology
文件頁數: 9/20頁
文件大?。?/td> 0K
描述: IC MULTIPLEXER 14-DFN
標準包裝: 91
系列: *
LTC4312
17
4312f
APPLICATIONS INFORMATION
Level Translating to Bus Voltages < 2.25V
The LTC4312 can be used for level translation to bus volt-
ages below 2.25V if certain conditions are met. In order
to perform this level translation, RTAs on the low voltage
side need to be disabled in order to prevent an over drive
of the low voltage bus. If one of the output channels is
pulled up to the low voltage bus supply, the other output
channel needs to be disabled when this channel is active,
in order to prevent cross conduction between the output
channels. Since the buffer turn-on and turn-off voltages
are 0.3 VMIN, the minimum bus supply voltage is deter-
mined by equation 5:
VDD,BUS(MIN)
0.3 VMIN
0.7
(5)
in order to meet the VIH = 0.7 VDD,BUS requirement and
not impact the high side noise margin. Users willing to live
with a lower logic high noise margin can level translate
down to 1.5V. An example of voltage level translation from
3.3V to 1.8V is illustrated in Figure 11, where a 3.3V input
voltage level is translated to a 1.8V output voltage level on
channel 1. Tying VCC to 3.3V satises equation 5. Ground-
ing VCC2 disables the RTA on the low voltage channel.
VMIN defaults to VCC under these conditions, making the
buffer turn off voltage 0.99V. Channel 2 must be disabled
when channel 1 is enabled. A similar voltage translation
can also be performed going from a 3.3V bus supply on
the output side to a 1.8V bus supply on the input side if
ACC is tied high to disable the input RTA and if VCC and
VCC2 are tied to the output side bus supply.
Figure 11. Level Shifting Down to 1.8V Using the LTC4312, VCC2 Is Grounded to Disable the Rise Time Accelerator
on the Low Voltage Bus. ENABLE2 Must Be Low Whenever ENABLE1 Is High
LTC4312
GND
VCC
VCC2
4312 F11
SCLOUT1
SDAOUT1
SCLOUT2
SDAOUT2
SCLOUT1
SDAOUT1
SCLOUT2
SDAOUT2
SCLIN
SDAIN
ENABLE1
ENABLE2
ACC
DISCEN
FAULT
3.3V
R2
10k
R1
10k
SCLIN
SDAIN
ENABLE1
ENABLE2
C1
0.01μF
3.3V
1.8V
R5
10k
R4
10k
C2
0.01μF
C3
0.01μF
5V
R7
10k
R6
10k
R3
10k
相關PDF資料
PDF描述
VI-J6R-IY-F3 CONVERTER MOD DC/DC 7.5V 50W
D38999/26SD97PN CONN PLUG 12POS STRAIGHT W/PINS
LTC4312CMS#PBF IC MULTIPLEXER 16-MSOP
MS3106A36-52S CONN PLUG 52POS STRAIGHT W/SCKT
VI-J6R-IY-F2 CONVERTER MOD DC/DC 7.5V 50W
相關代理商/技術參數
參數描述
LTC4312IMS#PBF 功能描述:IC MULTIPLEXER 16-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器,中繼器,分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP(10x10) 包裝:托盤 其它名稱:Q5134101
LTC4312IMS#TRPBF 功能描述:IC MULTIPLEXER 16-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器,中繼器,分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP(10x10) 包裝:托盤 其它名稱:Q5134101
LTC4313CDD-1#PBF 功能描述:IC 2WIRE BUS BUFFER 8DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器,中繼器,分配器 系列:- 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP(10x10) 包裝:托盤 其它名稱:Q5134101
LTC4313CDD-1#TRPBF 功能描述:IC 2WIRE BUS BUFFER 8DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器,中繼器,分配器 系列:- 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP(10x10) 包裝:托盤 其它名稱:Q5134101
LTC4313CDD-2#PBF 功能描述:IC 2WIRE BUS BUFFER 8DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器,中繼器,分配器 系列:- 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP(10x10) 包裝:托盤 其它名稱:Q5134101