參數資料
型號： LTC4313IMS8-3#PBF
廠商： Linear Technology
文件頁數： 16/20頁
文件大?。?/td> 0K
描述： IC 2WIRE BUS BUFFER 8MSOP
標準包裝： 50
類型： 2線總線緩沖器
Tx/Rx類型： I²C Logic
電容 - 輸入： 10pF
電源電壓： 2.9 V ~ 5.5 V
電流 - 電源： 8.1mA
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 管件
LTC4313-1/LTC4313-2/
LTC4313-3
5
4313123f
pin FuncTions
ENABLE (Pin 1): Connection Enable Input. When driven
low, the ENABLE pin isolates SDAIN and SCLIN from
SDAOUT and SCLOUT, asserts READY low, disables
rise time accelerators and inhibits automatic clock and
stop bit generation during a stuck low fault condition.
When driven high, the ENABLE pin connects SDAIN and
SCLIN to SDAOUT and SCLOUT after a stop bit or bus idle
has been detected on both busses. Driving ENABLE high
also enables automatic clock generation during a stuck
low fault condition. During a stuck low fault condition, a
risingedgeontheENABLEpinforcesaconnectionbetween
SDAIN and SDAOUT and SCLIN and SCLOUT. When using
the LTC4313 in a Hot Swap application with staggered
connector pins, connect a 10k resistor between ENABLE
and GND to ensure correct functionality. Connect to VCC
if unused.
SCLOUT (Pin 2): Serial Bus 2 Clock Input/Output. Connect
this pin to the SCL bus segment where stuck low recovery
is desired. Connect an external pull-up resistor or current
sourcebetweenthispinandthebussupply.Thebussupply
needs to be ≥ VCC for the LTC4313-1 and LTC4313-2, but
not for the LTC4313-3. Refer to the Applications Informa-
tion section for more details. Do not leave open.
SCLIN (Pin 3): Serial Bus 1 Clock Input/Output. Connect
this pin to the SCL line on the upstream bus. Connect
an external pull-up resistor or current source between
this pin and the bus supply. The bus supply needs to be
≥ VCC for the LTC4313-1 and LTC4313-2, but not for the
LTC4313-3. Refer to the Applications Information section
for more details. Do not leave open.
GND (Pin 4): Device Ground.
READY (Pin 5): Connection Ready Status Output. This
open drain N-channel MOSFET output pulls low when
the input and output sides are disconnected. READY is
pulled high when ENABLE is high and a connection has
been established between the input and output. Connect
a pull-up resistor, typically 10k from this pin to the bus
pull-up supply. Leave open or tie to GND if unused.
SDAIN (Pin 6): Serial Bus 1 Data Input/Output. Connect
this pin to the SDA line on the upstream bus. Connect an
externalpull-upresistororcurrentsourcebetweenthispin
and the bus supply. The bus supply needs to be ≥ VCC for
the LTC4313-1 and LTC4313-2, but not for the LTC4313-3.
Refer to the Applications Information section for more
details. Do not leave open.
SDAOUT (Pin 7): Serial Bus 2 Data Input/Output. Connect
this pin to the SDA bus segment where stuck low recovery
is desired. Connect an external pull-up resistor or current
sourcebetweenthispinandthebussupply.Thebussupply
needs to be ≥ VCC for the LTC4313-1 and LTC4313-2, but
not for the LTC4313-3. Refer to the Applications Informa-
tion section for more details. Do not leave open.
VCC (Pin 8): Power Supply Voltage. Power this pin from
a supply between 2.9V and 5.5V. Bypass with at least
0.01F to GND.
Exposed Pad (Pin 9, DD8 Package Only): Exposed pad
may be left open or connected to device GND.
相關PDF資料
PDF描述
VI-J6T-IY-F3 CONVERTER MOD DC/DC 6.5V 50W
VI-J6T-IY-F1 CONVERTER MOD DC/DC 6.5V 50W
LTC4315CMS#PBF IC 2WIRE BUS BUFFER 12MSOP
LTC4315CDE#PBF IC 2WIRE BUS BUFFER 12DFN
PT08E-14-19P CONN PLUG 19 POS R/A W/PINS
相關代理商/技術參數
參數描述
LTC4314CGN#PBF 功能描述:IC MULTIPLEXER 20-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101
LTC4314CGN#TRPBF 功能描述:IC MULTIPLEXER 20-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101
LTC4314CUDC#PBF 功能描述:IC MULTIPLEXER 20-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101
LTC4314CUDC#TRPBF 功能描述:IC MULTIPLEXER 20-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101
LTC4314IGN#PBF 功能描述:IC MULTIPLEXER 20-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*