- 您現在的位置：買賣IC網 > PDF目錄377779 > LTC4441IS8-1 (LINEAR TECHNOLOGY CORP) N-Channel MOSFET Gate Driver PDF資料下載
參數資料
| 型號： | LTC4441IS8-1 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | MOSFETs |
| 英文描述： | N-Channel MOSFET Gate Driver |
| 中文描述： | 6 A BUF OR INV BASED MOSFET DRIVER, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SO-8 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 154K |
| 代理商： | LTC4441IS8-1 |
LTC4441/LTC4441-1
44411f
6
PIU
PGND (Pin 1/Pin 1):
Driver Ground. Connect the DRV
CC
bypass capacitor directly to this pin, as close as possible
to the IC. In addition, connect the PGND and SGND pins
together close to the IC, and then connect this node to the
source of the power MOSFET (or current sense resistor)
with as short and wide a PCB trace as possible.
BLANK (Pin 2
/NA
):
Current Sense Blanking Output. Use
this pin to assert a blanking time in the power MOSFET’s
source current sense signal. The LTC4441 pulls this
open-drain output to SGND if the driver output is low. The
output becomes high impedance after a programmable
blanking time from the driver leading edge output. This
blanking time can be adjusted with the RBLANK pin.*
RBLANK (Pin 3/NA):
Blanking Time Adjust Input. Connect
a resistor from this pin to SGND to set the blanking time.
A small resistor value gives a shorter delay. Leave this pin
floating if the BLANK pin is not used.*
SGND (Pin 4/Pin 2):
Signal Ground. Ground return for the
DRV
CC
regulator and low power circuitry.
IN (Pin 5/Pin 3):
Driver Logic Input. This is the non-
inverting driver input under normal operating conditions.
*Available only on the lo-lead version of the LTC4441.
EN/SHDN (Pin 6/Pin 4):
Enable/Shutdown Input. Pulling
this pin above 1.21V allows the driver to switch. Pulling
this pin below 1.09V forces the driver output to go
low. Pulling this pin below 0.45V forces the LTC4441/
LTC4441-1 into shutdown mode; the DRV
CC
regulator
turns off and the supply current drops below 12
μ
A.
FB (Pin 7/Pin 5):
DRV
CC
Regulator Feedback Input. Con-
nect this pin to the center tap of an external resistive
divider between DRV
CC
and SGND to program the DRV
CC
regulator output voltage. To ensure loop stability, use the
value of 330k
for the top resistor, R1.
V
IN
(Pin 8/Pin 6):
Main Supply Input. This pin powers the
DRV
CC
linear regulator. Bypass this pin to SGND with a 1
μ
F
ceramic, tantalum or other low ESR capacitor in close
proximity to the LTC4441/LTC4441-1.
DRV
CC
(Pin 9/Pin 7):
Linear Regulator Output. This output
pin powers the driver and the control circuitry. Bypass this
pin to PGND using a 10
μ
F ceramic, low ESR (X5R or X7R)
capacitor in close proximity to the LTC4441/LTC4441-1.
OUT (Pin 10/Pin 8):
Driver Output.
Exposed Pad (Pin 11/NA):
Ground. The Exposed Pad
must be soldered to the PCB ground.
I
VIN
vs f
IN
I
VIN
vs C
LOAD
TYPICAL PERFOR U
f
IN
(kHz)
0
300
100 200
400 500 600 700
900
800
1000
I
V
4441 G21
50
45
20
15
5
10
0
40
35
30
25
T
A
= 25
°
C
C
LOAD
= 4.7nF
DRV
CC
= 5V
DRV
CC
= 9V
C
LOAD
(nF)
0
15
5
10
20 25 30 35
45
40
50
I
V
4441 G22
60
50
20
10
0
40
30
T
A
= 25
°
C
f
IN
= 100kHz
DRV
CC
= 5V
DRV
CC
= 9V
MSOP/SO-8
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4441-1 | RV Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 15V; Output Voltage (Vdc): 24V; Power: 2W; High Isolation 2W Converter; Approved for Medical Applications; EN and UL Safety Certificates; 6kVDC Isolation; Skinny DIP24 Package; Optional Continuous Short Circuit Protected; Fully Encapsulated; Very Low Isolation Capacitance |
| LTC4441EMSE | N-Channel MOSFET Gate Driver |
| LTC4441IMSE | RV Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 15V; Output Voltage (Vdc): 3.3V; Power: 2W; High Isolation 2W Converter; Approved for Medical Applications; EN and UL Safety Certificates; 6kVDC Isolation; Skinny DIP24 Package; Optional Continuous Short Circuit Protected; Fully Encapsulated; Very Low Isolation Capacitance |
| LTC485IN8 | Low Power RS485 Interface Transceiver |
| LTC485 | Low Power RS485 Interface Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4441IS8-1#PBF | 功能描述:IC MOSFET DRIVER N-CH 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LTC4441IS8-1#TRPBF | 功能描述:IC MOSFET DRIVER N-CH 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LTC4441MPMSE#PBF | 功能描述:IC MOSFET DRIVER N-CH 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LTC4441MPMSE#TRPBF | 功能描述:IC MOSFET DRIVER N-CH 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LTC4442EMS8E#PBF | 功能描述:IC MOSFET DRIVER N-CH 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:95 系列:- 配置:半橋 輸入類型:PWM 延遲時間:25ns 電流 - 峰:1.6A 配置數:1 輸出數:2 高端電壓 - 最大（自引導啟動）:118V 電源電壓:9 V ~ 14 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:管件 產品目錄頁面:1282 (CN2011-ZH PDF) 其它名稱:*LM5104M*LM5104M/NOPBLM5104M |
發布緊急采購，3分鐘左右您將得到回復。