the largest expected sense voltage gives IOUT = 1" />
參數資料
型號： LTC6102HMS8-1#PBF
廠商： Linear Technology
文件頁數： 6/26頁
文件大?。?/td> 0K
描述： IC AMP CURRENT SENSE 8-MSOP
標準包裝： 50
放大器類型： 電流檢測
電路數： 1
增益帶寬積： 200kHz
電流 - 輸入偏壓： 60pA
電壓 - 輸入偏移： 3µV
電流 - 電源： 420µA
電流 - 輸出 / 通道： 1mA
電壓 - 電源，單路/雙路(±)： 4 V ~ 60 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 管件
產品目錄頁面： 1322 (CN2011-ZH PDF)
LTC6102
LTC6102-1/LTC6102HV
14
6102fd
the largest expected sense voltage gives IOUT = 1mA, then
the maximum output dynamic range is available. Output
dynamic range is limited by both the maximum allowed
output current (Note 1) and the maximum allowed output
voltage, as well as the minimum practical output signal. If
less dynamic range is required, then RIN can be increased
accordingly, reducing the output current and power dis-
sipation. If small sense currents must be resolved ac-
curately in a system that has very wide dynamic range, a
smaller RIN may be used if the max current is limited in
another way, such as with a Schottky diode across RSENSE
(Figure 3). This will reduce the high current measurement
accuracy by limiting the result, while increasing the low
current measurement resolution. This approach can be
helpful in cases where occasional large burst currents
may be ignored.
APPLICATIONS INFORMATION
the LTC6102, and into ROUT via the OUT pin. In order to
minimize gain error, –INS should be routed in a separate
path from –INF to a point as close to RIN as possible. In
addition, the higher potential terminal of RIN should be
connected directly to the positive terminal of RSENSE (or
any input voltage source). For the highest accuracy, RIN
should be a four-terminal resistor if it is less than 10Ω.
Selection of External Output Resistor, ROUT
The output resistor, ROUT, determines how the output cur-
rent is converted to voltage. VOUT is simply IOUT ROUT.
In choosing an output resistor, the max output voltage
must rst be considered. If the circuit that is driven by the
output does not have a limited input voltage, then ROUT
must be chosen such that the max output voltage does
not exceed the LTC6102 max output voltage rating. If the
following circuit is a buffer or ADC with limited input range,
then ROUT must be chosen so that IOUT(MAX) ROUT is less
than the allowed maximum input range of this circuit.
In addition, the output impedance is determined by ROUT. If
the circuit to be driven has high enough input impedance,
then almost any output impedance will be acceptable.
However, if the driven circuit has relatively low input imped-
ance, or draws spikes of current, such as an ADC might
do, then a lower ROUT value may be required in order to
preserve the accuracy of the output. As an example, if the
input impedance of the driven circuit is 100 times ROUT,
then the accuracy of VOUT will be reduced by 1% since:
VI
RR
OUT
IN DRIVEN
OUT
IN DRIVEN
=
+
=
()
IIR
IR
OUT
.
100
101
099
=
Error Sources
The current sense system uses an amplier and resistors
to apply gain and level shift the result. The output is then
dependent on the characteristics of the amplier, such as
gain and input offset, as well as resistor matching.
Figure 3. Shunt Diode Limits Maximum Input Voltage to Allow
Better Low Input Resolution Without Overranging
V+
LOAD
DSENSE
6102 F03
RSENSE
Care should be taken when designing the PC board lay-
out for RIN, especially for small RIN values. All trace and
interconnect impedances will increase the effective RIN
value, causing a gain error. It is important to note that the
large temperature drift of copper resistance will cause a
change in gain over temperature if proper care is not taken
to reduce this effect.
To further limit the effect of trace resistance on gain,
maximizing the accuracy of these circuits, the LTC6102 has
been designed with a Kelvin input. The inverting terminal
(–INS) is separate from the feedback path (–INF). During
operation, these two pins must be connected together.
The design of the LTC6102 is such that current into –INS
is input bias current only, which is typically 60pA at 25°C.
Almost all of the current from RIN ows into –INF, through
相關PDF資料
PDF描述
PBC05SGBN CONN HEADER .100 SINGL R/A 5POS
PBC13SGAN CONN HEADER .100 SINGL R/A 13POS
PBC05SBDN CONN HEADER .100 SINGL R/A 5POS
AD8639ARZ-REEL7 IC OPAMP CHOPPER R-R DUAL 8SOIC
PEC05SBEN CONN HEADER .100 SINGL R/A 5POS
相關代理商/技術參數
參數描述
LTC6102HMS8-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Precision Zero Drift Current Sense Amplifi er
LTC6102HMS8-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Precision Zero Drift Current Sense Amplifi er
LTC6102HV 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage, Bidirectional Current Sense Amplifier Low Power Shutdown <10μA
LTC6102HVCDD#PBF 功能描述:IC AMP CURRENT SENSE 8-DFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT
LTC6102HVCDD#TRPBF 功能描述:IC AMP CURRENT SENSE 8-DFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*