- 您現在的位置：買賣IC網 > PDF目錄8609 > LTC6406IUD#TRPBF (Linear Technology)IC DIFF AMP/DRIVER R-R 16-QFN PDF資料下載
參數資料
| 型號： | LTC6406IUD#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 2/24頁 |
| 文件大小： | 0K |
| 描述： | IC DIFF AMP/DRIVER R-R 16-QFN |
| 標準包裝： | 2,500 |
| 類型： | ADC 驅動器 |
| 應用： | 數據采集 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-QFN-EP（3x3） |
| 包裝： | 帶卷 (TR) |
LTC6406
10
6406fc
SHDN (Pin 1/Pin 7): When SHDN is oating or directly
tied to V+, the LTC6406 is in the normal (active) operat-
ing mode. When the SHDN pin is connected to V–, the
LTC6406 enters into a low power shutdown state with
Hi-Z outputs.
V+, V– (Pins 2, 10, 11 and Pins 3, 9, 12/Pins 3, 6): Power
Supply Pins. It is critical that close attention be paid to
supply bypassing. For single supply applications it is
recommended that a high quality 0.1μF surface mount
ceramic bypass capacitor be placed between V+ and V– with
direct short connections. In addition, V– should be tied
directly to a low impedance ground plane with minimal
routing. For dual (split) power supplies, it is recommended
that additional high quality, 0.1μF ceramic capacitors are
used to bypass V+ to ground and V– to ground, again
with minimal routing. For driving large loads (<200
Ω),
additional bypass capacitance may be needed for optimal
performance. Keep in mind that small geometry (e.g. 0603
or smaller) surface mount ceramic capacitors have a much
higher self resonant frequency than do leaded capacitors,
and perform best in high speed applications.
VOCM (Pin 4/Pin 2): Output Common Mode Reference
Voltage. The voltage on VOCM sets the output common
mode voltage level (which is dened as the average of the
voltages on the +OUT and –OUT pins). The VOCM voltage
is internally set by a resistive divider between the supplies,
developing a default voltage potential of 1.25V with a 3V
supply. The VOCM pin can be overdriven by an external
voltage capable of driving the 18k
Ω Thevenin equivalent
impedance presented by the pin. The VOCM pin should be
bypassed with a high quality ceramic bypass capacitor of at
least 0.01μF, to minimize common mode noise from being
converted to differential noise by impedance mismatches
both externally and internally to the IC.
VTIP (Pin 5/NA): This pin can normally be left oating.
It determines which pair of input transistors (NPN or
PNP or both) is sensing the input signal. The VTIP pin is
set by an internal resistive divider between the supplies,
developing a default 1.55V voltage with a 3V supply. VTIP
has a Thevenin equivalent resistance of approximately
15k and can be overdriven by an external voltage. The
VTIP pin should be bypassed with a high quality ceramic
bypass capacitor of at least 0.01μF. See the Applications
Information section for more details.
+OUT, –OUT (Pins 7, 14/Pins 4, 5): Unltered Output
Pins. Besides driving the feedback network, each pin
can drive an additional 50
Ω to ground with typical short-
circuit current limiting of ±55mA. Each amplier output
(QFN/MSOP)
TYPICAL PERFORMANCE CHARACTERISTICS (MSOP Package)
PIN FUNCTIONS
Harmonic Distortion vs Frequency
Harmonic Distortion
vs Input Common Mode Voltage
Harmonic Distortion
vs Input Amplitude
FREQUENCY (MHz)
DISTOR
TION
(dBc)
6406 G34
–30
–40
–50
–60
–70
–80
–90
–100
–110
10
100
VS = 3V
VOCM = VICM = 1.25V
RLOAD = 800Ω
VOUTDIFF = 2VP-P
SINGLE-ENDED INPUT
2ND, RI = RF = 150Ω
2ND, RI = RF = 500Ω
3RD, RI = RF = 150Ω
3RD, RI = RF = 500Ω
INPUT COMMON MODE VOLTAGE (V)
6406 G35
DISTOR
TION
(dBc)
–40
–50
–60
–70
–80
–90
–100
0
3.0
2.5
2.0
1.5
1.0
0.5
2ND
3RD
VS = 3V
VOCM = 1.25V
fIN = 50MHz
RLOAD = 800Ω
RI = RF = 500Ω
VOUTDIFF = 2VP-P
SINGLE-ENDED INPUT
INPUT AMPLITUDE (dBm)
6406 G36
DISTOR
TION
(dBc)
–40
–50
–60
–70
–80
–90
–100
–4
10
8
6
4
2
0
–2
VS = 3V
VOCM = VICM =1.25V
fIN = 50MHz
RLOAD = 800Ω
RI = RF = 500Ω
SINGLE-ENDED INPUT
2ND
3RD
(0.4VP-P)
(2VP-P)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-24M-IV-F2 | CONVERTER MOD DC/DC 10V 150W |
| SY88703VKG TR | IC POST AMP PECL LP LIMIT 10MSOP |
| VE-24V-IV-F1 | CONVERTER MOD DC/DC 5.8V 150W |
| VE-22H-MY-B1 | CONVERTER MOD DC/DC 52V 50W |
| SY88943VKG TR | IC POST AMP PECL LIMITING 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC6409 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 14-Bit 250Msps |
| LTC6409CUDB#PBF | 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:OP-AMP DIFFERENTIAL 10GHZ 3 制造商:Linear Technology 功能描述:OP-AMP, DIFFERENTIAL, 10GHZ, 3300V/us, QFN-10; No. of Amplifiers:1; Input Offset Voltage:300V; Bandwidth:10GHz; Amplifier Case Style:QFN; No. of Pins:10; Supply Voltage Range:2.7V to 5.25V; Slew Rate:3300V/s; Supply Current:52mA ;RoHS Compliant: Yes |
| LTC6409CUDB#TRMPBF | 功能描述:IC AMP/DRIVER DIFF 10-QFN RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| LTC6409CUDB#TRMPBF | 制造商:Linear Technology 功能描述:IC OP-AMP 10GHz 3300V/ 1.4mV QFN- 制造商:Linear Technology 功能描述:IC, OP-AMP, 10GHz, 3300V/s, 1.4mV, QFN- |
| LTC6409CUDB#TRPBF | 功能描述:IC AMP/DRIVER DIFF GBW 10-QFN RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。