- 您現在的位置：買賣IC網 > PDF目錄377782 > LTC690M (Linear Technology Corporation) Microprocessor Supervisory Circuits PDF資料下載
參數資料
| 型號： | LTC690M |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Microprocessor Supervisory Circuits |
| 中文描述： | 微處理器監控電路 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 141K |
| 代理商： | LTC690M |
8
LTC 690/LTC 691
LTC 694/LTC 695
U
S
A
Microprocessor Reset
O
PPLICATI
W
U
I FOR ATIO
U
the reset voltage threshold, LOW LINE goes low. LOW
LINE returns high as soon as V
CC
rises above the reset
voltage threshold.
Battery Switchover
The battery switchover circuit compares V
CC
to the V
BATT
input, and connects V
OUT
to whichever is higher. When
V
CC
rises to 70mV above V
BATT
, the battery switchover
comparator, C2, connects V
OUT
to V
CC
through a charge
pumped NMOS power switch, M1. When V
CC
falls to
50mV above V
BATT
, C2 connects V
OUT
to V
BATT
through a
PMOS switch, M2. C2 has typically 20mV of hysteresis to
prevent spurious switching when V
CC
remains nearly
equal to V
BATT
. The response time of C2 is approximately
20
μ
s.
During normal operation, the LTC690 family uses a charge
pumped NMOS power switch to achieve low dropout and
low supply current. This power switch can deliver up to
50mA to V
OUT
from V
CC
and has a typical on resistance of
5
. The V
OUT
pin should be bypassed with a capacitor of
0.1
μ
F or greater to ensure stability. Use of a larger bypass
capacitor is advantageous for supplying current to heavy
transient loads.
When operating currents larger than 50mA are required
from V
OUT
, or a lower dropout (V
CC
-V
OUT
voltage differen-
tial) is desired, the LTC691 and LTC695 should be used.
These products provide BATT ON output to drive the base
The LTC690 family uses a bandgap voltage reference and
a precision voltage comparator C1 to monitor the 5V
supply input on V
CC
(see Block Diagram). When V
CC
falls
below the reset voltage threshold, the RESET output is
forced to active low state. The reset voltage threshold
accounts for a 5% variation on V
CC
, so the RESET output
becomes active low when V
CC
falls below 4.75V (4.65V
typical). On power-up, the RESET signal is held active low
for a minimum of 35ms for the LTC690/LTC691 (140ms
for the LTC694/LTC695) after reset voltage threshold is
reached to allow the power supply and microprocessor to
stabilize. The reset active time is adjustable on the LTC691/
LTC695. On power-down, the RESET signal remains ac-
tive low even with V
CC
as low as 1V. This capability helps
hold the microprocessor in stable shutdown condition.
Figure 1 shows the timing diagram of the RESET signal.
The precision voltage comparator, C1, typically has 40mV
of hysteresis which ensures that glitches at V
CC
pin do not
activate the RESET output. Response time is typically
10
μ
s. To help prevent mistriggering due to transient loads,
V
CC
pin should be bypassed with a 0.1
μ
F capacitor with the
leads trimmed as short as possible.
The LTC691 and LTC695 have two additional outputs:
RESET and LOW LINE. RESET is an active high output and
is the inverse of RESET. LOW LINE is the output of the
precision voltage comparator C1. When V
CC
falls below
V
CC
t
1
t
1
= RESET ACTIVE TIME
V1 = RESET VOLTAGE THRESHOLD
V2 = RESET VOLTAGE THRESHOLD +
RESET THRESHOLD HYSTERESIS
t
1
V2
V2
V1
V1
690 F01
RESET
LOW LINE
Figure 1. Reset Active Time
相關PDF資料 |
PDF描述 |
|---|---|
| LTC691C | Microprocessor Supervisory Circuits |
| LTC691CN | Microprocessor Supervisory Circuits |
| LTC691I | Microprocessor Supervisory Circuits |
| LTC691ISW | Microprocessor Supervisory Circuits |
| LTC690MJ8 | OSCILLATOR 27.00MHZ SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC690MJ8 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC691 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC6910-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Digitally Controlled Programmable Gain Amplifiers in SOT-23 |
| LTC6910-1CTS8 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Digitally Controlled Programmable Gain Amplifiers in SOT-23 |
| LTC6910-1CTS8#PBF | 制造商:Linear Technology 功能描述:SP Amp Variable Gain Amp Single R-R I/O 制造商:Linear Technology 功能描述:1 Programmable Gain Amplifier Bulk 制造商:Linear Technology 功能描述:AMPLIFIER, PROG GAIN, 11MHZ, TSOT-23-8; No. of Amplifiers:1; Bandwidth:11MHz; Supply Voltage Range:2.7V to 10.5V; Amplifier Case Style:TSOT-23; No. of Pins:8; No. of Channels:1; Rail To Rail I/O Type:Rail-Rail I/O ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。