- 您現在的位置：買賣IC網 > PDF目錄5335 > LTC6910-2ITS8#TRMPBF (Linear Technology)IC PGA DIGITAL R-R I/O TSOT23-8 PDF資料下載
參數資料
| 型號： | LTC6910-2ITS8#TRMPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 6/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PGA DIGITAL R-R I/O TSOT23-8 |
| 標準包裝： | 500 |
| 放大器類型： | 可編程增益 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 16 V/µs |
| 增益帶寬積： | 13MHz |
| 電壓 - 輸入偏移： | 1500µV |
| 電流 - 電源： | 3.5mA |
| 電流 - 輸出 / 通道： | 35mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 10.5 V，±2.7 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-8 薄型，TSOT-23-8 |
| 供應商設備封裝： | TSOT-23-8 |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | LTC6910-2ITS8#PBF LTC6910-2ITS8#PBF-ND |
LTC6910-1
LTC6910-2/LTC6910-3
14
6910123fa
OUT (Pin 1): Analog Output. This is the output of an
internal operational amplifier and swings to near the
power supply rails (V+ and V–) as specified in the Electrical
Characteristics table. The internal op amp remains active
at all times, including the zero gain setting (digital input
000). As with other amplifier circuits, loading the output as
lightly as possible will minimize signal distortion and gain
error. The Electrical Characteristics table shows perfor-
mance at output currents up to 10mA and current limits
that occur when the output is shorted to midsupply at 2.7V
and
±5V supplies. Signal outputs above 10mA are pos-
sible but current-limiting circuitry will begin to affect
amplifier performance at approximately 20mA. Long-term
operation above 20mA output is not recommended. Do
not exceed maximum junction temperature of 150
°C. The
output will drive capacitive loads up to 50pF. Capacitances
higher than 50pF should be isolated by a series resistor to
preserve AC stability.
AGND (Pin 2): Analog Ground. The AGND pin is at the
midpoint of an internal resistive voltage divider, develop-
ing a potential halfway between the V+ and V– pins, with an
equivalent series resistance to the pin of nominally 5k
(Figure 4). AGND is also the noninverting input of the
internal op amp, which makes it the ground reference
voltage for the IN and OUT pins. Because of this, very
“clean” grounding is important, including an analog ground
plane surrounding the package.
Recommended analog ground plane connection depends
on how power is applied to the LTC6910-X (Figures 1, 2,
and 3). Single power supply applications typically use V–
for the system signal ground. The analog ground plane in
single-supply applications should therefore tie to V–, and
the AGND pin should be bypassed to this ground plane by
a high quality capacitor of at least 1
F (Figure 1). The
AGND pin then provides an internal analog reference
voltage at half the supply voltage (with internal resistance
of approximately 5k
) which is the center of the swing
range for both input and output. Dual supply applications
with symmetrical supplies (such as
±5V) have a natural
system ground at zero volts, which can drive the analog
ground plane; AGND then connects directly to the ground
plane, making zero volts the input and output reference
voltage for the LTC6910-X (Figure 2). Finally, if a dual
power supply is asymmetrical, the supply ground is still
the natural ground plane voltage. To maximize signal
swing capability with an asymmetrical supply, however, it
is often desirable to refer the LTC6910-X’s analog input
and output to a voltage equidistant from the two supply
rails V+ and V–. The AGND pin will provide such a potential
when open-circuited and bypassed with a capacitor (Fig-
ure 3), just as with a single power supply, but now the
ground plane connection is different and the LTC6910-X’s
V+ and V– pins are both isolated from this ground plane.
UU
U
PI FU CTIO S
LTC6910-X
DIGITAL GROUND PLANE
(IF ANY)
ANALOG
GROUND
PLANE
1
SINGLE-POINT
SYSTEM GROUND
23
4
REFERENCE
V+
2
6910 F01
876
5
0.1
F
V+
1
F
LTC6910-X
DIGITAL GROUND PLANE
(IF ANY)
ANALOG
GROUND
PLANE
1
SINGLE-POINT
SYSTEM GROUND
23
4
6910 F02
876
5
0.1
F
V+
0.1
F
V–
Figure 2. Symmetrical Dual Supply
Ground Plane Connection
Figure 1. Single Supply
Ground Plane Connection
LTC6910-X
DIGITAL GROUND PLANE
(IF ANY)
ANALOG
GROUND
PLANE
1
SINGLE-POINT
SYSTEM GROUND
23
4
6910 F03
876
5
0.1
F
V+
0.1
F
1
F
V–
MID-SUPPLY
REFERENCE
Figure 3. Asymmetrical Dual
Supply Ground Plane Connection
相關PDF資料 |
PDF描述 |
|---|---|
| EL5257IY | IC AMP DUAL 600MHZ V-FB 8-MSOP |
| MMD25-050 | CONN RACK/PANEL 50POS 5A |
| MMB25-0501G1 | CONN RACK/PANEL 50POS 5A |
| 7010.9790.57 | FUSE 500MA 125V FAST F PCB SMD |
| ZEN132V130A24LS | POLYZEN 13.2V PPTC/ZENER SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC6910-3 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Digitally Controlled Programmable Gain Amplifiers in SOT-23 |
| LTC6910-3CTS8 | 制造商:Linear Technology 功能描述:SP Amp Variable Gain Amp Single R-R I/O ±5.25V/10.5V 8-Pin TSOT-23 |
| LTC6910-3CTS8#PBF | 制造商:Linear Technology 功能描述:SP Amp Variable Gain Amp Single R-R I/O ±5.25V/10.5V 8-Pin TSOT-23 |
| LTC6910-3CTS8#TR | 功能描述:IC PGA DIGITAL R-R OUT TSOT23-8 RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| LTC6910-3CTS8#TRM | 功能描述:IC PGA DIGITAL R-R OUT TSOT-23-8 RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。