參數資料
型號： LTH2911HTS8-2#TRM
廠商： LINEAR TECHNOLOGY CORP
元件分類： 電源管理
英文描述： POWER SUPPLY SUPPORT CKT, PDSO8
封裝： PLASTIC, MO-193, TSOT-23, 8 PIN
文件頁數： 3/20頁
文件大小： 245K
代理商： LTH2911HTS8-2#TRM
LTC2911
11
2911f
LTC2911-2, LTC2911-3 and LTC2911-4 respectively. V2
of the LTC2911-5 option is a high impedance input with
a nominal 0.5V threshold.
Input Noise Filtering for RST
TheV1,V2andADJcomparatorshavearesponsetimethat
is inversely proportional to overdrive. This characteristic
is illustrated in the Typical Performance Characteristics
as the graph Allowable Glitch Duration versus Overdrive.
The ADJ and the LTC2911-5’s V2 pin may be bypassed
withacapacitortoincreasethefilteringinapplicationsthat
demand it. The resultant RC lowpass filter at the inputs will
further reject high frequency components, at the cost of
slowing the monitor’s response to fault conditions.
Resistor Selection for ADJ
The threshold of the supply monitored by the ADJ pin is
configured with an external resistive divider (R2 and R1)
connected between the supply and ground. The tap point
for the divider is connected to the adjustable input (ADJ)
which has a 0.5V threshold. (See Figure 2)
Normally, the user selects a trip voltage based on the sup-
ply and acceptable tolerances, and a value of R1 based on
current drawn. For a given current, I, R1 is given by:
R1
=
0.5V
I
TominimizeerrorsarisingfromtheADJinputbiascurrent,
a value of less than 100k is recommended for R1.
R2 is then chosen by:
R2
=R1
VTRIP_ ADJ
0.5V
– 1
where, VTRIP_ADJ is the supply threshold when the ADJ
pin falls below its 0.5V threshold.
For accurate monitoring, the resistor tolerance should be
as small as possible. Resistor tolerance of 0.1% or some
trimming of components should be considered for R2/R1
in applications that require an accurate trip point.
Resistor Selection for PFI
Anexternalresistivedivider(R3andR4)connectedbetween
the supply and ground configures the threshold of the
supply monitored by the power-fail comparator. The tap
point for the divider is connected to the PFI input which
has a 0.5V threshold. (See Figure 3a)
Resistor selection follows a process similar to that for
the ADJ pin.
R3 is given by:
R3
=
0.5V
I
APPLICATIONS INFORMATION
–
+
+–
0.5V
2911 F02
ADJ
LTC2911
R2
R1
VTRIP
Figure 2. Setting the Adjustable (ADJ) Trip Point
相關PDF資料
PDF描述
LTI2911ITS8-3#TR POWER SUPPLY SUPPORT CKT, PDSO8
LTC2911CDDB-3#TRPBF POWER SUPPLY SUPPORT CKT, PDSO8
LTC2911CTS8-5#TRM POWER SUPPLY SUPPORT CKT, PDSO8
LTH2911HTS8-1#TRM POWER SUPPLY SUPPORT CKT, PDSO8
LTI2911ITS8-4#TRMPBF POWER SUPPLY SUPPORT CKT, PDSO8
相關代理商/技術參數
參數描述
LTH-301-05 功能描述:光學開關（透射型，光電晶體管輸出） Photointerrupter Phototransistor RoHS:否 制造商:Omron Electronics 輸出設備:Phototransistor 槽寬:3.4 mm 光圈寬度:0.5 mm 集電極—發射極最大電壓 VCEO:30 V 最大集電極電流:20 mA 正向電流: 安裝風格:Through Hole 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝:
LTH-301-07 功能描述:光學開關（透射型，光電晶體管輸出） Photointerrupter Phototransistor RoHS:否 制造商:Omron Electronics 輸出設備:Phototransistor 槽寬:3.4 mm 光圈寬度:0.5 mm 集電極—發射極最大電壓 VCEO:30 V 最大集電極電流:20 mA 正向電流: 安裝風格:Through Hole 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝:
LTH301-07 制造商:Lite-On Semiconductor Corporation 功能描述:
LTH-301-07P1 制造商:LITEON 制造商全稱:Lite-On Technology Corporation 功能描述:Property of LITE-ON Only
LTH-301-07P2 制造商:LITEON 制造商全稱:Lite-On Technology Corporation 功能描述:Property of LITE-ON Only
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*