- 您現在的位置：買賣IC網 > PDF目錄358957 > LTL42CB6N (LITE-ON ELECTRONICS INC) 3mm LED(Water Clear) PDF資料下載
參數資料
| 型號： | LTL42CB6N |
| 廠商： | LITE-ON ELECTRONICS INC |
| 元件分類： | LED |
| 英文描述： | 3mm LED(Water Clear) |
| 中文描述： | T-1 SINGLE COLOR LED, BLUE, 3 mm |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 556K |
| 代理商： | LTL42CB6N |
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household applications).Consult Liteon’s Sales in advance for information on
applications in which exceptional reliability is required, particularly when the failure or malfunction of the
LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment,
medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are used within three months.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in
a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.
4. Lead Forming & Assembly
During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens.
Do not use the base of the lead frame as a fulcrum during forming.
Lead forming must be done before soldering, at normal temperature.
During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress.
5. Soldering
When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point.
Dipping the lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering conditions :
Soldering iron
Wave soldering
Temperature
Soldering time
300°C Max.
3 sec. Max.
(one time only)
Pre-heat
Pre-heat time
Solder wave
Soldering time
100°C Max.
60 sec. Max.
260°C Max.
10 sec. Max.
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or
catastrophic failure of the LED
Part No. : LTL42CB6N
Page : 7 of 10
BNS-OD-C131/A4
相關PDF資料 |
PDF描述 |
|---|---|
| LTM-9034-1 | MB 61C 61#20 SKT PLUG |
| LTM-9034-2 | MB 3C 3#20 SKT PLUG |
| LTM-9034-3 | MB 6C 6#20 PIN PLUG |
| LTM-9034-4 | MB 6C 6#20 PIN PLUG |
| LTM-9034-9 | MB 6C 6#20 SKT PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTL42CW65AT | 功能描述:標準LED-通孔 White Clear RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| LTL-42D1NMHCP | 功能描述:LED 電路板指示器 Housing LED ThruHole 3mm 2Lvl Grn/Yellow RoHS:否 制造商:Lumex LED 大小:3 mm 照明顏色:Green 波長:565 nm 光強度:30 mcd 安裝類型:SMD/SMT 顯示角:60 deg 封裝:Reel |
| LTL-42D1NMHDP1 | 功能描述:LED 電路板指示器 Housing LED ThruHole 3mm 2Lvl Grn/Yellow RoHS:否 制造商:Lumex LED 大小:3 mm 照明顏色:Green 波長:565 nm 光強度:30 mcd 安裝類型:SMD/SMT 顯示角:60 deg 封裝:Reel |
| LTL-42D1NMHLP | 功能描述:LED 電路板指示器 Housing LED ThruHole 3mm 4Lvl Yellow/Grn RoHS:否 制造商:Lumex LED 大小:3 mm 照明顏色:Green 波長:565 nm 光強度:30 mcd 安裝類型:SMD/SMT 顯示角:60 deg 封裝:Reel |
| LTL-42DGNMHDP1 | 功能描述:LED 電路板指示器 Housing LED ThruHole 3mm 2Lvl Green RoHS:否 制造商:Lumex LED 大小:3 mm 照明顏色:Green 波長:565 nm 光強度:30 mcd 安裝類型:SMD/SMT 顯示角:60 deg 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。