參數資料
型號： LTPH245
廠商： Seiko Instruments Inc.
英文描述： LINE THERMAL PRINTER MECHANISM TECHNICAL REFERENCE
中文描述： 熱敏打印機芯線技術參考
文件頁數： 9/64頁
文件大?。?/td> 841K
代理商： LTPH245
1-2
1.2 DESIGN AND HANDLING PRECAUTIONS
To maintain the initial level of performance of the printer and to prevent future problems from occurring,
observe the following precautions.
1.2.1 Design Precautions
If too much energy is applied to the thermal head, it may overheat and become damaged.
Always use the printer with the specified amount of energy.
Do not apply a pulse of 2V and 20 nsec or higher to each signal terminal of the thermal head.
Use C-MOS IC chips (74HC240 or equivalent) for interfacing the CLK, LATCH, DAT and DST
signals of the thermal head.
When turning the power on or off, always DISABLE (put in “Low” state) the DST terminals.
To prevent the thermal head from being damaged by static electricity:
Fix the printer to the Frame Ground (FG) with the FG connector as shown in
Figure 7-2
.
Connect the GND terminal (SG) to FG through 1 M
resistor so that the electric potential
of the SG of the thermal head and the FG of the printer are equal.
Keep the Vp power off when not printing to prevent the thermal head from becoming
electrically corroded.
Wire resistance should be 50 m
or less (however the less the better) between the power
supply and the Vp, and the GND terminals on the thermal head controller. Maintain a
considerable distance from signal lines to reduce electrical interference.
The surge voltage between Vp and GND should not exceed 10 V.
As a noise countermeasure, connect the capacitor noted below between the Vdd and GND
terminals near the thermal head control connector.
Vp
GND:
Vdd
GND:
approximately 10
μ
F
approximately 1
μ
F
When turning the power on or off, perform the Vp and Vcc simultaneously or in the order of 1)
and 2) as follows:
At power ON:
At power OFF:
1) Vcc (5 V)
1) Vp
→
2) Vp
2) Vcc (5 V)
→
Always monitor the output of the platen position sensor and paper detector. Incorrect
activation of the thermal head may damage and reduce the longevity of the thermal head and
the platen.
Design the outer case so that the paper detector is not affected by light from outside. Since a
reflection type photo interrupter is used in the paper detector, the detector may be affected by
light from outside.
相關PDF資料
PDF描述
LTR-516AD HIGH PHOTO SENSITIVITY
LTS-3401VE Common Anode, Rt. & lt. Hand decimal
LTS-3403LE The LTS-3403LE is a 0.8 inch (20.32 mm) digit height single digit seven-segment display
LTS-3403LG The LTS-3403LG is a 0.8 inch (20.32 mm) digit height single digit seven-segment display
LTS-3403LY The LTS-3403LY is a 0.8 inch (20.32 mm) digit height single digit seven-segment display
相關代理商/技術參數
參數描述
LTPH245D-C384-E 功能描述:打印機 76.8X38X16 384 DOTS RoHS:否 制造商:Seiko Instruments 產品:Printer 電源電壓: 每行點數:9 x 320 打印速度:52.5 cps, 80 cps 紙張寬度:112 mm
LTPH245E-C384-E 制造商:Seiko Instruments Inc (SII) 功能描述:
LTPK006EB3010/25 制造商:Nexans 功能描述:6-F I/O PLENUM ARMORED 10GIG 50UM FIBER
LTPL-C023WS57 功能描述:大功率LED - 白色 3 W Power LED 95lm Cool Wht 5000-6500K RoHS:否 制造商:Cree, Inc. 照明顏色:Cool White 顏色溫度:5000 K 光通量:280 lm 顯示角:125 deg 正向電流:700 mA 正向電壓:2.9 V 安裝風格:SMD/SMT 系列:XMLBWW 封裝:Reel
LTPL-C025WS 功能描述:大功率LED - 白色 3 W Power LED 95lm Cool Wht 5000-6500K RoHS:否 制造商:Cree, Inc. 照明顏色:Cool White 顏色溫度:5000 K 光通量:280 lm 顯示角:125 deg 正向電流:700 mA 正向電壓:2.9 V 安裝風格:SMD/SMT 系列:XMLBWW 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*