- 您現(xiàn)在的位置：買賣IC網 > PDF目錄377766 > LTTJ (Linear Integrated Systems) Precision Extended Bandwidth, RMS-to-DC Converter PDF資料下載
參數資料
| 型號： | LTTJ |
| 廠商： | Linear Integrated Systems |
| 英文描述： | Precision Extended Bandwidth, RMS-to-DC Converter |
| 中文描述： | 精密擴展帶寬，有效值- DC轉換器 |
| 文件頁數： | 12/28頁 |
| 文件大?。?/td> | 328K |
| 代理商： | LTTJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
12
LTC1967
1967f
Input Connections
The LTC1967 input is differential and DC coupled. The
LTC1967 responds to the RMS value of the differential
voltage between Pin 2 and Pin 3, including the DC portion
of that difference. However, there is no DC-coupled path
from the inputs to ground. Therefore, at least one of the two
inputs must be connected with a DC-return path to ground.
Both inputs must be connected to something. If either
input is left floating, a zero volt output will result.
For single-ended DC-coupled applications, simply con-
nect one of the two inputs (they are interchangeable) to
the signal, and the other to ground. This will work well for
dual supply configurations, but for single supply con-
figurations it will only work well for unipolar input sig-
nals. The LTC1967 input voltage range is from rail-to-rail,
and when the input is driven above V
+
or below GND the
gain and offset errors will increase substantially after just
a few hundred millivolts of overdrive. Fortunately, most
single supply circuits measuring a DC-coupled RMS
value will include some reference voltage other than
ground, and the second LTC1967 input can be connected
to that point.
For single-ended AC-coupled applications, Figure 9 shows
three alternate topologies. The first one, shown in Figure
9a uses a coupling capacitor to one input while the other
is grounded. This will remove the DC voltage difference from
the input to the LTC1967, and it will therefore not be part
of the resulting output voltage. Again, this connection will
APPLICATIOU
W
U
U
work well with dual supply configurations, but in single
supply configurations it will be necessary to raise the volt-
age on the grounded input to assure that the signal at the
active input stays within the range of 0V to V
+
. If there is
already a suitable voltage reference available, connect the
second input to that point. If not, a midsupply voltage can
be created with two resistors as shown in Figure 9b.
Finally, if the input voltage is known to be between 0V and
V
+
, it can be AC coupled by using the configuration shown
in Figure 9c. Whereas the DC return path was provided
through Pin 3 in Figures 9a and 9b, in this case, the return
path is provided on Pin 2, through the input signal volt-
ages. The switched capacitor action between the two input
pins of the LTC1967 will cause the voltage on the coupling
capacitor connected to the second input to follow the DC
average of the input voltage.
For differential input applications, connect the two inputs to
the differential signal. If AC coupling is desired, one of the
two inputs can be connected through a series capacitor.
In all of these connections, to choose the input coupling
capacitor, C
C
, calculate the low frequency coupling time
constant desired, and divide by the LTC1967 differential
input impedance. Because the LTC1967 input impedance
is about 100 times its output impedance, this capacitor is
typically much smaller than the output averaging capaci-
tor. Its requirements are also much less stringent, and a
ceramic chip capacitor will usually suffice.
Figure 9. Single-Ended AC-Coupled Input Connection Alternatives
+
LTC1967
GND
V
+
V
+
V
+
V
–
(9a)
C
C
IN1
V
IN
IN2
2
3
LTC1967
(9b)
C
C
R1
20k
R2
20k
IN1
V
IN
V
+
IN2
2
3
LTC1967
(9c)
C
C
IN1
V
IN
1967 F07
V
DC
IN2
2
3
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1968 | Precision Wide Bandwidth, RMS-to-DC Converter |
| LTC1968CMS8 | Precision Wide Bandwidth, RMS-to-DC Converter |
| LTC1968IMS8 | Precision Wide Bandwidth, RMS-to-DC Converter |
| LTC1980 | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| LTC1980EGN | Combination Battery Charger and DC/DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTTLDL250C | 制造商:TECHNITROL 功能描述: |
| LTTLDL500C | 制造商:TECHNITROL 功能描述: |
| L-TTSI001161BL-2-DB | 制造商:AGERE 制造商全稱:AGERE 功能描述:1k x 1k Time-Slot Interchanger |
| L-TTSI002321BL-2-DB | 制造商:AGERE 制造商全稱:AGERE 功能描述:2k x 2k Time-Slot Interchanger |
| L-TTSI004321BL-2-DB | 制造商:AGERE 制造商全稱:AGERE 功能描述:4k x 4k Time-Slot Interchanger |
發(fā)布緊急采購，3分鐘左右您將得到回復。