- 您現在的位置：買賣IC網 > PDF目錄367613 > LUCL8560AAU-D GT 5C 2#0 3#12 SKT RECP WALL PDF資料下載
參數資料
| 型號： | LUCL8560AAU-D |
| 英文描述： | GT 5C 2#0 3#12 SKT RECP WALL |
| 中文描述： | 低功耗振鈴用戶接口 |
| 文件頁數： | 43/46頁 |
| 文件大小： | 842K |
| 代理商： | LUCL8560AAU-D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁
Lucent Technologies Inc.
43
Data Sheet
April 2000
L8560 Low-Power SLIC with Ringing
Applications
(continued)
Design Examples
(continued)
Blocking Capacitors
5-6401b(F)
Figure 40. ac Interface Using First-Generation Codec (Including Blocking Capacitors) for Complex
Termination Impedance
If a 5 V only codec such as the Lucent T7504 is used, dc blocking capacitors must be added as shown in Figure
40. This is because the codec is referenced to 2.5 V and the SLIC to ground—with the ac coupling, a dc bias at
T/R is eliminated and power associated with this bias is not consumed.
Typically, values of 0.1 μF to 0.47 μF capacitors are used for dc blocking. The addition of blocking capacitors will
cause a shift in the return loss and hybrid balance frequency response toward higher frequencies, degrading the
lower-frequency response. The lower the value of the blocking capacitor, the more pronounced the effect is, but
the cost of the capacitor is lower. It may be necessary to scale resistor values higher to compensate for the
low-frequency response. This effect is best evaluated via simulation. A
PSPICE
* model for the L8560 is available.
Design equation calculations seldom yield standard component values. Conversion from the calculated value to
standard value may have an effect on the ac parameters. This effect should be evaluated and optimized via simu-
lation.
* PSPICEis a registered trademark of MicroSim Corporation.
0.1
μ
F
R
TGS
V
TX
R
TGP
= 4.32 k
T
XI
V
ITR
R
T6
R
x
R
T3
R
HB
CODEC
OUTPUT
DRIVE
AMP
CODEC
OP AMP
–
+
19.2
C
N
R
N1
R
N2
R
GP
R
RCV
RCVN
RCVP
–I
T/R
207.36
C
GS
C
B1
2.5 V
C
B2
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL8560AAU-DT | GT 3C 3#0 SKT RECP WALL RM |
| LUCL8560AP-D | Top Entry Connector Hood; Enclosure Material:Aluminum Alloy; For Use With:C146 Rectangular Circular Connectors; Thread Size:PG 21; Connecting Termination:Screw; No. of Contacts:16; Operating Voltage:400V; Series:C-146 RoHS Compliant: Yes |
| LUCL8560AP-DT | Side Entry Connector Hood; Enclosure Material:Aluminum Alloy; For Use With:C146 Rectangular Circular Connectors; Thread Size:PG 21; Connecting Termination:Screw; No. of Contacts:24; Operating Voltage:400V; Series:C-146 RoHS Compliant: Yes |
| LUCL8560AU-D | Low-Power SLIC with Ringing |
| LUCL8560AU-DT | Low-Power SLIC with Ringing |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL8560AAU-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Power SLIC with Ringing |
| LUCL8560AP-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Power SLIC with Ringing |
| LUCL8560AP-DT | 制造商:Major 功能描述: |
| LUCL8560AU | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Subscriber Line Interface Circuit |
| LUCL8560AU-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Power SLIC with Ringing |
發布緊急采購，3分鐘左右您將得到回復。