參數資料
型號: LUCL9216GGF-D
英文描述: Short-Loop Ringing SLIC with Ground Start
中文描述: 短環振鈴用戶接口與地面開始
文件頁數: 37/48頁
文件大?。?/td> 1062K
代理商: LUCL9216GGF-D
Preliminary Data Sheet
September 2001
Short-Loop Ringing SLIC with Ground Start
L9216A/G
Agere Systems Inc.
37
ac Applications
(continued)
Design Examples
(continued)
First-Generation Codec ac Interface Network—
Complex Termination
The reference circuit in Figure 26 shows the complete
SLIC schematic for interface to the Agere T7504 first-
generation codec for the German complex termination
impedance. For this example, the ac interface was
designed for a 220
+ (820
|| 115 nF) complex
termination and hybrid balance with transmit gain and
receive gain set to 0 dBm. For illustration purposes,
1 Vrms PPM injection was assumed in this example.
This implies the overhead voltage is increased to
7.24 V and no meter pulse rejection is required. Also,
this example illustrates the device using fixed overhead
and current limit.
Complex Termination Impedance Design Example
The gain shaping necessary for a complex termination
impedance may be done by shaping across the AX
amplifier at nodes ITR and VTX.
Complex termination is specified in the form:
5-6396(F)
To work with this application, convert termination to the
form:
5-6398(F)
where:
R
1
′ = R
1
+ R
2
1
R
2
R
2
′ =
(R
1
+ R
2
)
C′ =
C
ac Interface Using First-Generation Codec
R
GX
/R
TGS
/C
GS
(Z
TG
): these components give gain shap-
ing to get good gain flatness. These components are a
scaled version of the specified complex termination
impedance.
Note for pure (600
) resistive terminations, compo-
nents R
TGS
and C
GS
are not used. Resistor R
GX
is used
and is still 4750
.
R
X
/R
T6
: with other components set, the transmit gain
(for complex and resistive terminations) R
X
and R
T6
are
varied to give specified transmit gain.
R
T3
/R
RCV
/R
GP
: for both complex and resistive termina-
tions, the ratio of these resistors sets the receive gain.
For resistive terminations, the ratio of these resistors
sets the return loss characteristic. For complex termi-
nations, the ratio of these resistors sets the low-fre-
quency return loss characteristic.
C
N
/R
N1
/R
N2
: for complex terminations, these compo-
nents provide high-frequency compensation to the
return loss characteristic.
For resistive terminations, these components are not
used and RCVN is connected to ground via a resistor.
R
HB
: sets hybrid balance for all terminations.
Set Z
TG
—Gain Shaping:
Z
TG
= R
GX
|| R
TGS
+ C
GS
which is a scaled version of
Z
T/R
(the specified termination resistance) in the
R
1
′ || R
2
′ + C′ form.
R
GX
must be 4750
to set SLIC transconductance to
300 V/A.
R
GX
= 4750
At dc, C
GS
and C′ are open.
R
GX
= M x R
1
where M is the scale factor.
R
1
M =
It can be shown:
R
TGS
= M x R
2
and
C
TGS
=
R
2
C
R
1
R
1
C′
R
2
-------
+
R
1
R
2
---------------------
2
--------------
M
------
相關PDF資料
PDF描述
LUCL9216GGF-DT Short-Loop Ringing SLIC with Ground Start
LUCL9216ARG-D Short-Loop Ringing SLIC with Ground Start
LUCL9216AGF-D Short-Loop Ringing SLIC with Ground Start
LUCL9216AGF-DT Short-Loop Ringing SLIC with Ground Start
LUCL9216GRG-D CONNECTOR ACCESSORY
相關代理商/技術參數
參數描述
LUCL9216GGF-DT 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start
LUCL9216GRG-D 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start
LUCL9217AAR-D 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM
LUCL9217AAR-DT 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM
LUCL9217GAR-D 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM