- 您現在的位置：買賣IC網 > PDF目錄367614 > LUCL9217AAR-D GT 3C 3#16S PIN PLUG PDF資料下載
參數資料
| 型號： | LUCL9217AAR-D |
| 英文描述： | GT 3C 3#16S PIN PLUG |
| 中文描述： | 低成本線接口，具有反向電池和PPM |
| 文件頁數： | 22/30頁 |
| 文件大?。?/td> | 414K |
| 代理商： | LUCL9217AAR-D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
22
Agere Systems Inc.
Data Sheet
November 2001
with Reverse Battery and PPM
L9217A/G Low-Cost Line Interface
Applications
(continued)
Periodic Pulse Metering (PPM)
Periodic pulse metering (PPM), also referred to as
TTX, is input to the PPMIN input of the L9217. Upon
application of appropriate logic control, this signal is
presented to the tip/ring subscriber loop. The state of
the L9217 may be changed while applying PPM sig-
nals. The L9217 assumes that a shaped PPM signal is
applied to the PPMIN input.
Sufficient drive current is available in the tip and ring
drive amplifiers to support 3.5 Vrms PPM signals into a
200
load with a 45 mA dc current limit.
PPM signals are input to a separate PPMIN input. This
input is controlled via the logic table. PPMIN is off dur-
ing all states except the forward/reverse PPM active
state. Thus, PPM signals may be present at all times,
even during non-PPM active times. To apply PPM to
tip/ring, from a normal overhead state first switch to a
high overhead state without PPM; the overhead volt-
age at tip/ring will increase to 7 V to 13 V. The ramp up
time of the overhead increase is on the order of hun-
dreds of milliseconds. Thus, wait 1 s before applying
the PPM signal by going to a PPM active high over-
head state. Once in a high overhead, there is no timing
requirement in switching in and out of a PPM active
mode. Without the initial 1 s delay, AT/AR will get into
saturation and PPM signal at T/R will get distorted, pro-
ducing crosstalk in the handset.
PPM input signals may be a maximum 0.525 Vrms at
PPMIN. The gain from PPMIN tip/ring is 10. Thus, for
2.5 Vrms at tip and ring, apply a 0.375 Vrms signal at
PPMIN. The PPM signal should be ac coupled to
PPMIN through a 0.01
μ
F capacitor.
When applied to tip and ring, the PPM signal will also
be returned through the SLIC and will appear at the
SLIC VITR output. The concern is that this high-voltage
signal can overload the codec input and cause distor-
tion of the (desired) ac signal. Therefore, some sort of
PPM rejection scheme must be employed, see Figure
1. The L9217 outputs on the PPMOUT pin, which is the
output of the PPM input amplifier. Connecting a resis-
tor, R
PPM,
from PPMOUT to node TG will provide a path
for a hybrid reject of the returned meter pulse signal.
The return path from tip and ring to VITR for the PPM
signal is through the internal AX amplifier. TG is the
input to this amplifier. Through R
PPM
, by applying a
PPM signal equal in magnitude, but 180 degrees out of
phase to the returned PPM signal at TG, the PPM sig-
nal is cancelled, preventing overload at the codec
input. Even if the cancellation is not perfect, the idea is
to reduce the PPM signal so as not to overload the
codec. Codecs typically have a low-pass filter at their
input to reject any residual meter pulse signal.
The value of R
PPM
is selected by:
R
PPM
=
[{(V
PPMIN
x
10)/(R
PPMLOAD
+
R
DC
+
2R
P
)}/201.2]
–1
For undistorted transmission of meter pulse signals,
increase the overhead as described in the Overhead
Voltage section of this data sheet.
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL9217AAR-DT | Low-Cost Line Interface with Reverse Battery and PPM |
| LUCL9217GAR-D | Aluminum Snap-In Capacitor; Capacitance: 10000uF; Voltage: 25V; Case Size: 25x30 mm; Packaging: Bulk |
| LUCL9217GAR-DT | Low-Cost Line Interface with Reverse Battery and PPM |
| LUCL9218AAR-D | Low-Cost Line Interface |
| LUCL9218AAR-DT | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:3; Connector Shell Size:16; Connecting Termination:Solder; Circular Shell Style:Square Flange Receptacle; Body Style:Straight |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL9217AAR-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| LUCL9217GAR-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| LUCL9217GAR-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| LUCL9218AAR-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
| LUCL9218AAR-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
發布緊急采購，3分鐘左右您將得到回復。