參數資料
型號： LUCL9310AP-D
元件分類： 圓形連接器
英文描述： Top Entry Connector Hood; Enclosure Material:Aluminum Alloy; For Use With:C146 Rectangular Circular Connectors; Thread Size:PG 21; Connecting Termination:Screw; Gender:Male; No. of Contacts:16; Operating Voltage:400V; Series:C-146 RoHS Compliant: Yes
中文描述： 線路接口和線路接入電路全功能用戶接口，振鈴繼電器，測試接入設備
文件頁數： 14/60頁
文件大?。?/td> 1053K
代理商： LUCL9310AP-D
Data Sheet
July 2001
Full-Feature SLIC, Ringing Relay, and Test Access Device
L9310 Line Interface and Line Access Circuit
14
Agere Systems Inc.
Operating States
Input State Coding
State control is via a tiered logic system. The device
must initially be set to a primary control state (B3 = 0).
This will set the operational state of the SLIC and
switch. The secondary control table (B3 = 1) is used to
turn on the PPM amplifier or to turn on the test circuitry
and enter a test state. The primary state of the device
(the state of the SLIC and switch) will not change when
entering a secondary control state.
Within the primary control table, each state will set the
SLIC and the switch to a specific mode. The exception
is the tip-amp and ring-amp states. The tip-amp and
ring-amp states will change the configuration of the
switches, but leave the state of the SLIC unchanged
from the previous primary control mode.
Once a primary (device) control state is selected, the
PPM or test circuitry can be activated via a secondary
control state. Within the secondary control table, there
are PPM active modes and test active modes. Upon
entering a test active mode in the secondary control
table, both TESTLEV output and TESTSIG input are
active and the test switches set to the appropriate con-
dition. (See Test Architecture Diagram, Figure 2.) An
exception is the V
REF
test active mode. Upon entering
V
REF
, only the TESTLEV output is active, and the inter-
nal (2.35 V typical) reference voltage appears at
TESTLEV. In the V
REF
mode, the TESTSIG input is
deactivated.
Once PPM is on, the user may reverse the battery in
the primary state table without turning off PPM. With
PPM, if the user goes to the scan, ring, or disconnect
mode in the primary table, PPM will be turned off.
Unlike PPM, the test feature, once on, will remain on if
the user transitions to forward active, reverse active,
scan, ring, or disconnect state in the primary state
table.
PPM or test is deactivated by selecting PPM/test off in
the secondary control table.
Data control is via a parallel latched data control
scheme. Data latches are edge-level sensitive. Data is
latched in when the LATCH control input goes low.
Data must be set up 200 ns before LATCH goes low
and held 50 ns after LATCH goes high. While LATCH is
low, the user should not change the data control inputs
at B0, B1, B2, and B3. The data control inputs at B0,
B1, B2, and B3 may only be changed when LATCH is
high. NSTAT supervision output is not controlled by the
LATCH control input.
相關PDF資料
PDF描述
LUCL9310AP-DT Side Entry Connector Hood; Enclosure Material:Aluminum Alloy; For Use With:C146 Rectangular Circular Connectors; Thread Size:PG 21; Connecting Termination:Screw; Gender:Male; No. of Contacts:24; Operating Voltage:400V; Series:C-146 RoHS Compliant: Yes
LUCL9312GP-D Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications
LUCL9312GP-DT Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications
LUCL9312AP-D Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications
LUCL9312AP-DT PLCC-Socket-Adapter 32-pin DIL to 32-pin PLCC for 8-Bit EPROMs
相關代理商/技術參數
參數描述
LUCL9310AP-DT 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
LUCL9310GP-D 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
LUCL9310GP-DT 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
LUCL9311AP-D 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access
LUCL9311AP-DT 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*