- 您現在的位置：買賣IC網 > PDF目錄67759 > LV51142T 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 PDF資料下載
參數資料
| 型號： | LV51142T |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封裝： | SOT-23, 6 PIN |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 212K |
| 代理商： | LV51142T |
LV51142T
Block Diagram
+
-
+
-
+
-
+
-
Oscillator
Counter
Level
Shifter
Control Circuit
Short Detector
Charge
Over-current
Detector
Discharge
Over-current
Detector
Over-discharge
Detector
Over-charge
Detector
VDD
VSS
CO
VM
DO
Measurement Conditions
Over-charge detection voltage, Over-charge hysteresis voltage --- [Circuit 1]
Set V1 = 3.0V and V2 = 0V. Over-charge detection voltage VC is V1 at which VCO goes "Low" from "High" when V1
is gradually increased from 3.0V. Then IC is released from the over-charge state and VCO goes "High" from "Low" at
the voltage "Measured VC-VHc" when V1 is gradually decreased.
If V2 is set to the greater value than discharge over-current detection voltage VIdc in the over-charge state, VHc is
canceled and then IC is released from the over-charge state at VC.
Over-discharge detection voltage --- [Circuit 1]
Set V1 = 3.0V and V2 = 0V. Over-discharge detection voltage Vdc is V1 at which VDO goes "Low" from "High" when
V1 is gradually decreased from 3.0V. Next, set V2 under to charge over-current detection voltage VIc. Then IC is
released from the over-discharge state at Vdc and VDO goes "High" from "Low".
Charge over-current detection voltage --- [Circuit 2]
Set V1 = 3.0V and V2 = 0V. Charge over-current detection voltage VIc is V2 at which VCO goes "Low" from "High"
when V2 is gradually decreased from 0V.
Discharge over-current detection voltage --- [Circuit 2]
Set V1 = 3.0V and V2 = 0V. Discharge over-current detection voltage VIdc is V2 at which VDO goes "Low" from
"High" when V2 is gradually increased from 0V.
Load short-circuiting detection voltage --- [Circuit 2]
Set V1 = 3.0V and V2 = 0V. Load short-circuiting detection voltage Vshort is V2 at which VDO goes "Low" from
"High" within a time between the minimum and the maximum value of load short-circuiting detection delay time tshort,
when V2 is increased rapidly within 10
μs.
0V battery charge starting charger voltage --- [Circuit 3]
Set V1 = V2 = 0V and decrease V2 gradually. 0V battery charge starting charger voltage Vcha is V2 when VCO goes
"High" (V1-0.1V or higher).
Continued on next page.
No.A1641-4/13
相關PDF資料 |
PDF描述 |
|---|---|
| LV51144T | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LV56801P | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PZFM15 |
| LV8111V | BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDSO44 |
| LV8711T | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| LV8732V | STEPPER MOTOR CONTROLLER, PDSO44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV51142T-TE-F-E | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LV51143T-TE-F-E | 制造商:Rochester Electronics LLC 功能描述: 制造商:ON Semiconductor 功能描述:Battery Management 制造商:ON Semiconductor 功能描述:REEL / 1-CELL LIB PROTECTION 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LV51144T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC 1-Cell Lithium-Ion Battery Protection IC |
| LV51144T-TE-F-E | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LV51146T-TE-F-E | 制造商:ON Semiconductor 功能描述:1-CELL LIB PROTECTION - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。