- 您現在的位置：買賣IC網 > PDF目錄69008 > LV8711T (SANYO SEMICONDUCTOR CO LTD) STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF資料下載
參數資料
| 型號： | LV8711T |
| 廠商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封裝： | 0.225 INCH, TSSOP-24 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 404K |
| 代理商： | LV8711T |
LV8711T
No.A1685-7/12
Input pin function
(1) Chip enable function
Standby mode / operating mode of the IC are switched by setting the PS pin. In the standby-state, the IC enters a
power saving mode and all logic is reset. In the standby-state, internal regulator circuit is not operative.
PS
Condition
Internal regulator
Low or Open
Standby mode
Standby
High
Operating mode
Operating
(2) STM output control logic
Parallel input
Output
IN1A(2A)
IN1B(2B)
OUT1A(2A)
OUT1B(2B)
Current direction
Low
OFF
Output OFF
High
Low
High
Low
OUTA to OUTB
Low
High
Low
High
OUTB to OUTA
High
Low
Brake(DCM mode)
(3) Constant-current setting
The constant-current control setting consist of the VREF voltage setting and resistor (RNF) connected between RNF
and ground. The current is set according to the following equation.
IOUT [A] = VREF [V] / 5 / RNF []
Also, the voltage applied to the VREF pin can be switched to four stages settings by the state of two inputs of the
ATT1 and ATT2 pins. This function is effective for power saving when the motor holding current is applied.
Attenuation function of the VREF input voltage
ATT1
ATT2
Current setting reference voltage attenuation ratio
Low
100%
High
Low
80%
Low
High
50%
High
20%
The output current calculation method for using of attenuation function of the VREF input voltage is as below.
IOUT = (VREF / 5) х Attenuation ratio / RNF resistance
e.g. When the VREF is 1.0V and the set reference voltage is 100% [(ATT1, ATT2) = (Low, Low)] and the RNF
resistance is 0.47, the following output current is set.
IOUT = 1.0V / 5 х 100% / 0.47 = 425mA
In this conditions, when (ATT1, ATT2) is set to (High, High),
IOUT = 425mA х 20% = 85mA
Therefore, the power saving is executable by attenuation of the output current when motor holding current is
supplied.
(4) Setting the chopping frequency
For constant-current control, chopping operation is made with the frequency determined by the external capacitor
(connected to the CHOP pin). The chopping frequency to be set with the capacitor connected to the CHOP pin (pin
10) is as shown below.
Chopping period: Tchop
Tchop ≈ C х V х 2 / I [s]
V: Threshold voltage
Typ, 0.5V
I : Charge / discharge current Typ. 10μA
Chopping frequency: Fchop
Fchop ≈ 1 / Tchop [Hz]
相關PDF資料 |
PDF描述 |
|---|---|
| LV8713T | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| LV8731V | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO44 |
| LV8772 | STEPPER MOTOR CONTROLLER, DIP28 |
| LX1675ILQ-TR | 1.5 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1675CLQ-TR | 1.5 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV8711T_11 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Constant-Current Control Stepping Motor Driver |
| LV8711TGEVB | 功能描述:電源管理IC開發工具 EVM FOR LV8711T RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LV8711TL-MPB-H | 制造商:ON Semiconductor 功能描述:STEPPING MOTOR DRIVER - Ammo Pack |
| LV8711TL-TLM-H | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LV8711T-MPB-H | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。