- 您現在的位置：買賣IC網 > PDF目錄69008 > LV8713T STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF資料下載
參數資料
| 型號： | LV8713T |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封裝： | 0.225 INCH, TSSOP-24 |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 296K |
| 代理商： | LV8713T |
LV8713T
No.A1918-15/16
(13) Current control timing chart(Chopping operation)
(Sine wave increasing direction)
(Sine wave decreasing direction)
In each current mode, the operation sequence is as described below :
At rise of chopping frequency, the CHARGE mode begins. (The Blanking section in which the CHARGE mode is
forced regardless of the magnitude of the coil current (ICOIL) and set current (IREF) exists for 1
μs.)
The coil current (ICOIL) and set current (IREF) are compared in this blanking time.
When (ICOIL < IREF) state exists ;
The CHARGE mode up to ICOIL
≥ IREF, then followed by changeover to the SLOW DECAY mode, and
finally by the FAST DECAY mode for approximately 1
μs.
When (ICOIL < IREF) state does not exist ;
The FAST DECAY mode begins. The coil current is attenuated in the FAST DECAY mode till one cycle of
chopping is over.
Above operations are repeated. Normally, the SLOW (+FAST) DECAY mode continues in the sine wave increasing
direction, then entering the FAST DECAY mode till the current is attenuated to the set level and followed by the SLOW
DECAY mode.
FAST
SLOW
CHARGE
FAST
SLOW
CHARGE
Current mode
fchop
Coil current
STEP
Set current
FAST
SLOW
FAST
SLOW
CHARGE
Current mode
fchop
Coil current
STEP
Set current
Forced CHARGE
section
CHARGE
Chopping cycle
BLANKING section
Chopping cycle
相關PDF資料 |
PDF描述 |
|---|---|
| LV8731V | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO44 |
| LV8772 | STEPPER MOTOR CONTROLLER, DIP28 |
| LX1675ILQ-TR | 1.5 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1675CLQ-TR | 1.5 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1684CDT | 1 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV8713TGEVB | 功能描述:電源管理IC開發工具 EVM FOR LV8713T RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LV8713T-MPB-H | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LV8713T-TLM-H | 功能描述:馬達/運動/點火控制器和驅動器 4-16V Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LV8727 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Current Control Stepping Motor Driver |
| LV8727-E | 功能描述:馬達/運動/點火控制器和驅動器 PRINTER DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。