參數資料
型號: LX1676-CPWTR
廠商: MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP
元件分類: 穩壓器
英文描述: 1.5 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO38
封裝: PLASTIC, TSSOP-38
文件頁數: 2/16頁
文件大?。?/td> 387K
代理商: LX1676-CPWTR
LX1676
PRELIMINARY DATA SHEET
Microsemi
Integrated Products Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 10
WWW
.Microse
m
i
.CO
M
Mobile AMD Athlon
VRM Controller
I N T E GR A T ED
PRODUCT S
Copyright
2000
Revision: 0.4b, 9/14/2004
TH EORY OF O PERATION (CONTINUED)
OVER-CURRENT PROTECTION (PHASE 3)
The hysteretic phase has its own current limit protection
because with it’s very fast response time with a 100 nH
inductor the upper MOSFET cannot be allowed to stay on
during an output short circuit condition. The phase 3 over-
current sensing uses the RDS(ON) of the upper MOSFET
with a resistor RSET to determine the over current limit
point. A current source draws 50uA through RSET which
determines the required drop across the MOSFET
RDS(ON) to initiate a current limit condition.
50 uA
+
_
RSET
Q2
+
_
Current Limit
Comparator
Q1
Vin
RDS(ON)
Vout
400nS Delay
ILIM3
VS3
Figure 4 – Phase 3 Current Limit
Phase 3 RSET is calculated by:
uA
50
RDSon
ILimit
Rset
=
OVER VOLTAGE PROTECTION
An over voltage protection circuit monitors the output
voltage and will latch all three phases off if an over voltage
condition (greater than 2.35 V) is detected.
Both
MOSFETs for phase 3 will be held off and the lower
MOSFETs for phase 1 and 2 will be held on to discharge
the output capacitor till the output voltage drops below .85
volt, at .85 volts all MOSFETs will be turned off.
FAULT LOGIC
There are a number of possible states that will cause a
fault condition that will disable the output MOSFET
drivers. A fault condition will be caused by the following:
Enable (ENA) pin being pulled low
Over-current condition on either phase 1 or phase 3
Over Voltage output > 2.35V
Under Voltage output < 0.85V
In all cases except Over Voltage all MOSFET drivers
will be latched off. For an Over Voltage fault the lower
MOSFETs for phase 1 and 2 will be held on to discharge
the bulk capacitance on the output till a lower limit of .85
volts is reached then all MOSFETS will be turned off.
To reset a fault it necessary to cycle the ENA pin low
then back high or remove and reapply the input voltage
VIN.
The Under Voltage monitor is not enabled until the
output voltage has ramped up to the level commanded by
the DACOUT pin and the PWGD output in high.
PWM FREQUENCY
An external resistor sets the PWM frequency from the
ROSC pin to ground.
The equation for ROSC is:
()
9
e
100
f
K
1
ROSC
+
=
where ROSC is in K, f is in Hz, K=105e-12
AA
PP
LL
IICC
AA
TT
IIOO
NN
SS
相關PDF資料
PDF描述
LX1732CDUT 1 A SWITCHING REGULATOR, 135 kHz SWITCHING FREQ-MAX, PDSO8
LX1801CLQ SPECIALTY ANALOG CIRCUIT, PQCC16
LX1801CLQ-TR SPECIALTY ANALOG CIRCUIT, PQCC16
LY5150ALH SPECIALTY ANALOG CIRCUIT, PBGA16
LY5150ALHTR SPECIALTY ANALOG CIRCUIT, PBGA16
相關代理商/技術參數
參數描述
LX1677 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:AMD64 Processor VRM Controller
LX1677 EVAL KIT 制造商:Microsemi Corporation 功能描述:PWM CONTROLLERS - Bulk
LX1677CLQ 功能描述:IC CTRLR VRM PS 2PHASE 38MLPQ RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源,ICERA E400,E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA,WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
LX1677CPW 功能描述:IC CTRLR VRM PS 2PHASE 38TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源,ICERA E400,E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA,WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
LX1681 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:VOLTAGE - MODE PWM CONTROLLERS