- 您現在的位置：買賣IC網 > PDF目錄367620 > LX1990ILM LED Driver PDF資料下載
參數資料
| 型號： | LX1990ILM |
| 元件分類： | LED驅動器 |
| 英文描述： | LED Driver |
| 中文描述： | LED驅動器 |
| 文件頁數： | 3/6頁 |
| 文件大小： | 83K |
| 代理商： | LX1990ILM |
LX1990 E
VALUATION
B
OARD
U
SER
G
UIDE
Copyright 2002
Rev. 0.1a, 4/9/02
Microsemi
Integrated Products
Page 3
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
W
M
.
C
L
X
1
9
0
S
E
R
G
U
I
D
E
O
VERVIEW
The LX1990 is a dual output current sink
optimized for driving light emitting diodes. The
evaluation board demonstrates how this low cost
bipolar IC enables precise current regulation in
LED display lighting applications, yet requires far
fewer parts than discrete solutions.
The evaluation board ships with two strings of
three LED’s each. Two green and one blue
connected in series to each output. Each LED
has a parallel connected jumper (JB2-JB7) that
allow the LED to be bypassed to remove it from
the circuit so various combinations of LED’s can
be easily configured for each series string. A
small rheostat (R1) in series with R2 (4.32K
which sets the maximum current at 30mA)
varies the R
SET
resistance such that the output
LED current will vary from about 5mA to 30mA.
Two other jumpers are included, JB1 which
enables the LX1990, and JB8 to which allows an
externally supplied PWM signal to toggle the
R
SET
resistance to allow duty cycle dimming.
Evaluation Board Features
Easily configured with 1 to 3 LED’s on
each output
Included rheostat allows output current to
be set from 5 to 30mA
Jumpers allow external PWM signal to
burst dim the LED’s and an external
enable control
E
VALUATION
B
OARD
O
PERATION
The evaluation board has four possible inputs of
which at least two must be used to operate the
circuit. These inputs are described in table 1
below.
The LX1990 integrated circuit itself requires a
input supply voltage (VDD) in the range of 2.7 to
5.5V. When using all three LED’s in series a
supply voltage of greater than 5.5V is required
on the VLOAD input, since the combined
forward voltage of the three LED’s at the rated
current of 20mA is about 8.4V. However if you
were to bypass as an example the two blue
LED’s by moving up the shorting blocks on JB4
and JB7 then a single 5V supply could be
connected at both VDD and VLOAD to drive the
remaining four LED’s or conversely the two
blue LED’s since both require a forward voltage
of about 4V. If you are willing to drive the blue
LED’s at only 5mA then voltages as low as 3.3V
will directly drive both the chip and the LED’s.
The other two inputs PWM and ENABLE allow
external control over dimming and shutdown.
The evaluation board comes with a built in 100K
pull-up resistor R3 that is connected between
the ENABLE input and VDD. R3 will enable the
outputs unless JB1 is set to OFF. When JB1 is
in the EXT/ON position enable is also connected
to the external ENABLE input TP5. An external
voltage signal or open collector logic can be
applied to this point to disable the device. This
external signal must be able to drive the 100K
pull-up resistor low (less than 0.8V).
Input
Allowable Range
Description
VDD
2.7 to 5.5V
LX1990 power supply. Quiescent current draw is between 1.4 and
4mA depending on voltage and temperature
LED voltage supply. Required voltage depends on forward voltage
requirements of LED’s and 100-400mV chip overhead
Input for external enable control, board ships with 100K pull-up to
VDD
Input to allow duty cycle dimming of output 150hz to 20Khz logic
signal, active high
Common ground reference
VLOAD
2 to 10V
ENABLE
0 to VDD
PWM
0 to VDD
GND
0V
Table 1
– Evaluation Board Connections
相關PDF資料 |
PDF描述 |
|---|---|
| LX1991-01EVALKIT | LED Driver |
| LX1991-03EVALKIT | LED Driver |
| LX1992-01EVALKIT | LED Driver |
| LX1992-02EVALKIT | LED Driver |
| LX1992-CDU | LED Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX1990ILM-TR | 功能描述:IC LED DRIVER LINEAR 6-MLP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LX1991 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Six Output Programmable LED Current Sink |
| LX1991 EVAL KIT | 功能描述:KIT EVALUATION FOR LED DRIVER RoHS:是 類別:編程器，開發系統 >> 評估板 - LED 驅動器 系列:- 標準包裝:1 系列:PowerWise® 電流 - 輸出 / 通道:20mA 輸出及類型:1，非隔離 輸出電壓:17V 特點:可調光 輸入電壓:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相關產品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| LX1991-01EVALKIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED Driver |
| LX1991-02EVAL | 功能描述:BOARD EVAL LED DRIVER 6CHANNEL RoHS:是 類別:編程器，開發系統 >> 評估板 - LED 驅動器 系列:- 標準包裝:1 系列:PowerWise® 電流 - 輸出 / 通道:20mA 輸出及類型:1，非隔離 輸出電壓:17V 特點:可調光 輸入電壓:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相關產品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
發布緊急采購，3分鐘左右您將得到回復。