- 您現在的位置：買賣IC網 > PDF目錄377793 > LX8384-00CDD (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) 5A LOW DROPOUT POSITIVE REGULATORS PDF資料下載
參數資料
| 型號： | LX8384-00CDD |
| 廠商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 5A LOW DROPOUT POSITIVE REGULATORS |
| 中文描述： | 1.2 V-8 V ADJUSTABLE POSITIVE LDO REGULATOR, 1.5 V DROPOUT, PSSO3 |
| 封裝： | PLASTIC, TO-263, 3 PIN |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 216K |
| 代理商： | LX8384-00CDD |
5A L
OW
D
ROPOUT
P
OSITIVE
R
E G U L AT O R S
LX8384-xx/8384A-xx/8384B-xx
P R O D U C T D A T A B O O K 1 9 9 6 / 1 9 9 7
5
Copyright 1997
Rev. 1.9 12/97
P
R O D U C T I O N
D
A T A
S
H E E T
A P P L I C AT I O N N O T E S
The LX8384/84A/84B Series ICs are easy to use Low-Dropout (LDO)
voltage regulators. They have all of the standard self-protection
features expected of a voltage regulator: short circuit protection,
safe operating area protection and automatic thermal shutdown if
the device temperature rises above approximately 165°C.
Use of an output capacitor is REQUIRED with the LX8384/84A/
84B series. Please see the table below for recommended minimum
capacitor values.
These regulators offer a more tightly controlled reference voltage
tolerance and superior reference stability when measured against
the older pin-compatible regulator types that they replace.
STABILITY
The output capacitor is part of the regulator’s frequency compen-
sation system. Many types of capacitors are available, with different
capacitance value tolerances, capacitance temperature coefficients,
and equivalent series impedances. For all operating conditions,
connection of a 220μF aluminum electrolytic capacitor or a 47μF
solid tantalum capacitor between the output terminal and ground
will guarantee stable operation.
If a bypass capacitor is connected between the output voltage
adjust (ADJ) pin and ground, ripple rejection will be improved
(please see the section entitled “
RIPPLE REJECTION
”). When ADJ
pin bypassing is used, the required output capacitor value increases.
Output capacitor values of 220μF (aluminum) or 47μF (tantalum)
provide for all cases of bypassing the ADJ pin. If an ADJ pin bypass
capacitor is not used, smaller output capacitor values are adequate.
The table below shows recommended minimum capacitance values
for stable operation.
INPUT
10μF
10μF
OUTPUT
ADJ
None
15μF
15μF Tantalum, 100μF Aluminum
47μF Tantalum, 220μF Aluminum
To ensure good transient response from the power supply system
under rapidly changing current load conditions, designers generally
use several output capacitors connected in parallel. Such an
arrangement serves to minimize the effects of the parasitic resistance
(ESR) and inductance (ESL) that are present in all capacitors. Cost-
effective solutions that sufficiently limit ESR and ESL effects gener-
ally result in total capacitance values in the range of hundreds to
thousands of microfarads, which is more than adequate to meet
regulator output capacitor specifications. Output capacitance
values may be increased without limit.
The circuit shown in Figure 1 can be used to observe the transient
response characteristics of the regulator in a power system under
changing loads. The effects of different capacitor types and values
on transient response parameters, such as overshoot and under-
shoot, can be compared quickly in order to develop an optimum
solution.
RECOMMENDED CAPACITOR VALUES
FIGURE 1
— DYNAMIC INPUT and OUTPUT TEST
LX8384/84A
/84B
ADJ
Power Supply
OUT
IN
Star Ground
1 sec
10ms
R
DSON
<< R
L
Full Load
(Smaller resistor)
Minumum Load
(Larger resistor)
OVERLOAD RECOVERY
Like almost all IC power regulators, the LX8384/84A/84B regulators
are equipped with Safe Operating Area (SOA) protection. The SOA
circuit limits the regulator's maximum output current to progressively
lower values as the input-to-output voltage difference increases. By
limiting the maximum output current, the SOA circuit keeps the
amount of power that is dissipated in the regulator itself within safe
limits for all values of input-to-output voltage within the operating
range of the regulator. The LX8384/84A/84B SOA protection system
is designed to be able to supply some output current for all values
of input-to-output voltage, up to the device breakdown voltage.
Under some conditions, a correctly operating SOA circuit may
prevent a power supply system from returning to regulated opera-
tion after removal of an intermittent short circuit at the output of the
regulator. This is a normal mode of operation which can be seen in
most similar products, including older devices such as 7800 series
regulators. It is most likely to occur when the power system input
voltage is relatively high and the load impedance is relatively low.
When the power system is started “cold”, both the input and
output voltages are very close to zero. The output voltage closely
follows the rising input voltage, and the input-to-output voltage
difference is small. The SOA circuit therefore permits the regulator
to supply large amounts of current as needed to develop the
designed voltage level at the regulator output.
Now consider the case where the regulator is supplying regulated
voltage to a resistive load under steady state conditions. A moderate
input-to-output voltage appears across the regulator but the voltage
difference is small enough that the SOA circuitry allows sufficient
current to flow through the regulator to develop the designed output
voltage across the load resistance. If the output resistor is short-
circuited to ground, the input-to-output voltage difference across the
regulator suddenly becomes larger by the amount of voltage that had
appeared across the load resistor. The SOA circuit reads the
increased input-to-output voltage, and cuts back the amount of
current that it will permit the regulator to supply to its output
terminal. When the short circuit across the output resistor is
removed, all the regulator output current will again flow through the
output resistor. The maximum current that the regulator can supply
to the resistor will be limited by the SOA circuit, based on the large
input-to-output voltage across the regulator at the time the short
circuit is removed from the output. If this limited current is not
sufficient to develop the designed
voltage across the output resistor,
相關PDF資料 |
PDF描述 |
|---|---|
| LX8384-00CP | 5A LOW DROPOUT POSITIVE REGULATORS |
| LX8384-00IDD | 5A LOW DROPOUT POSITIVE REGULATORS |
| LX8384-00IP | 5A LOW DROPOUT POSITIVE REGULATORS |
| LX8384B-33CDD | 5A LOW DROPOUT POSITIVE REGULATORS |
| LX8384B-33CP | 5A LOW DROPOUT POSITIVE REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX8384-00CDDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Positive Adjustable Voltage Regulator |
| LX8384-00CDT | 制造商:Microsemi Corporation 功能描述:LOW DROP OUT REGULATOR - POSITIVE ADJUSTABLE - Bulk |
| LX8384-00CDTT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LX8384-00CP | 功能描述:IC REG LDO ADJ 5A TO220 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| LX8384-00IDD | 功能描述:IC REG LDO ADJ 5A TO263 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。