- 您現在的位置：買賣IC網 > PDF目錄39441 > M1MA141WKT3 (MOTOROLA INC) 2 ELEMENT, SILICON, SIGNAL DIODE PDF資料下載
參數資料
| 型號： | M1MA141WKT3 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 二極管(射頻、小信號、開關、功率) |
| 英文描述： | 2 ELEMENT, SILICON, SIGNAL DIODE |
| 文件頁數： | 3/6頁 |
| 文件大小： | 99K |
| 代理商： | M1MA141WKT3 |
M1MA141WKT1 M1MA142WKT1
3
Motorola Small–Signal Transistors, FETs and Diodes Device Data
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
mm
inches
0.035
0.9
0.075
0.7
1.9
0.028
0.65
0.025
0.65
0.025
SC–70/SOT–323 POWER DISSIPATION
The power dissipation of the SC–70/SOT–323 is a function
of the collector pad size. This can vary from the minimum
pad size for soldering to the pad size given for maximum
power dissipation. Power dissipation for a surface mount
device is determined by TJ(max), the maximum rated junction
temperature of the die, R
θJA, the thermal resistance from the
device junction to ambient; and the operating temperature,
TA. Using the values provided on the data sheet, PD can be
calculated as follows.
PD =
TJ(max) – TA
R
θJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25°C, one can
calculate the power dissipation of the device which in this
case is 150 milliwatts.
PD =
150
°C – 25°C
833
°C/W
= 150 milliwatts
The 833
°C/W assumes the use of the recommended
footprint on a glass epoxy printed circuit board to achieve a
power dissipation of 150 milliwatts. Another alternative would
be to use a ceramic substrate or an aluminum core board
such as Thermal Clad
. Using a board material such as
Thermal Clad, a power dissipation of 300 milliwatts can be
achieved using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference should be a maximum of 10
°C.
The soldering temperature and time should not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient should be 5
°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
相關PDF資料 |
PDF描述 |
|---|---|
| M2273VF300 | 2273 A, 3000 V, SILICON, RECTIFIER DIODE |
| M2273VC340 | 2273 A, 3400 V, SILICON, RECTIFIER DIODE |
| M2413VC240 | 2413 A, 2400 V, SILICON, RECTIFIER DIODE |
| M2413VF250 | 2413 A, 2500 V, SILICON, RECTIFIER DIODE |
| M2413VC220 | 2413 A, 2200 V, SILICON, RECTIFIER DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M1MA142K | 制造商:LUGUANG 制造商全稱:Shenzhen Luguang Electronic Technology Co., Ltd 功能描述:Surface Mount Switching Diodes |
| M1MA142KT1 | 功能描述:二極管 - 通用，功率，開關 80V 100mA RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
| M1MA142KT1G | 功能描述:二極管 - 通用，功率，開關 80V 100mA RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
| M1MA142WA | 制造商:LUGUANG 制造商全稱:Shenzhen Luguang Electronic Technology Co., Ltd 功能描述:Surface Mount Switching Diodes |
| M1MA142WAT1 | 功能描述:二極管 - 通用，功率，開關 80V 100mA RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。