- 您現在的位置：買賣IC網 > PDF目錄224123 > M25P32VMP6TP (意法半導體) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | M25P32VMP6TP |
| 廠商： | 意法半導體 |
| 元件分類： | FLASH |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 2/39頁 |
| 文件大?。?/td> | 506K |
| 代理商： | M25P32VMP6TP |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
M25P32
10/39
Hold Condition
The Hold (HOLD) signal is used to pause any se-
rial communications with the device without reset-
ting the clocking sequence. However, taking this
signal Low does not terminate any Write Status
Register, Program or Erase cycle that is currently
in progress.
To enter the Hold condition, the device must be
selected, with Chip Select (S) Low.
The Hold condition starts on the falling edge of the
Hold (HOLD) signal, provided that this coincides
with Serial Clock (C) being Low (as shown in Fig-
The Hold condition ends on the rising edge of the
Hold (HOLD) signal, provided that this coincides
with Serial Clock (C) being Low.
If the falling edge does not coincide with Serial
Clock (C) being Low, the Hold condition starts af-
ter Serial Clock (C) next goes Low. Similarly, if the
rising edge does not coincide with Serial Clock (C)
being Low, the Hold condition ends after Serial
Clock (C) next goes Low. (This is shown in Figure
During the Hold condition, the Serial Data Output
(Q) is high impedance, and Serial Data Input (D)
and Serial Clock (C) are Don’t Care.
Normally, the device is kept selected, with Chip
Select (S) driven Low, for the whole duration of the
Hold condition. This is to ensure that the state of
the internal logic remains unchanged from the mo-
ment of entering the Hold condition.
If Chip Select (S) goes High while the device is in
the Hold condition, this has the effect of resetting
the internal logic of the device. To restart commu-
nication with the device, it is necessary to drive
Hold (HOLD) High, and then to drive Chip Select
(S) Low. This prevents the device from going back
to the Hold condition.
Figure 7. Hold Condition Activation
AI02029D
HOLD
C
Hold
Condition
(standard use)
Hold
Condition
(non-standard use)
相關PDF資料 |
PDF描述 |
|---|---|
| M25P40SVMN6P/4 | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M25P40SVMN3G/4A | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M25P40-VMN6TG/X | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M25P40VMF6 | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P40VMF6G | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25P32-VMP6TP | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:32-Mbit, low voltage, serial Flash memory with 75 MHz SPI bus interface |
| M25P32-VMS6G | 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Trays |
| M25P32-VMS6TG | 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Tape and Reel |
| M25P32-VMW3GB | 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Trays |
| M25P32-VMW3TGB | 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3.3V 32Mbit 4M x 8bit 8ns 8-Pin SO W T/R |
發布緊急采購，3分鐘左右您將得到回復。