參數資料
型號: M25P64-VMF6TP
廠商: 意法半導體
元件分類: DRAM
英文描述: 4 Mbit Uniform Sector, Serial Flash Memory
中文描述: 4兆位統一部門,串行閃存
文件頁數: 26/38頁
文件大?。?/td> 519K
代理商: M25P64-VMF6TP
M25P64
26/38
POWER-UP AND POWER-DOWN
At Power-up and Power-down, the device must
not be selected (that is Chip Select (S) must follow
the voltage applied on V
CC
) until V
CC
reaches the
correct value:
V
CC
(min) at Power-up, and then for a further
delay of t
VSL
V
SS
at Power-down
Usually a simple pull-up resistor on Chip Select (S)
can be used to ensure safe and proper Power-up
and Power-down.
To avoid data corruption and inadvertent write op-
erations during Power-up, a Power On Reset
(POR) circuit is included. The logic inside the de-
vice is held reset while V
CC
is less than the Power
On Reset (POR) threshold voltage, V
WI
– all oper-
ations are disabled, and the device does not re-
spond to any instruction.
Moreover, the device ignores all Write Enable
(WREN), Page Program (PP), Sector Erase (SE),
Bulk Erase (BE) and Write Status Register
(WRSR) instructions until a time delay of t
PUW
has
elapsed after the moment that V
CC
rises above the
V
WI
threshold. However, the correct operation of
the device is not guaranteed if, by this time, V
CC
is
still below V
CC
(min). No Write Status Register,
Program or Erase instructions should be sent until
the later of:
These values are specified in
Table 8.
.
If the delay, t
VSL
, has elapsed, after V
CC
has risen
above V
CC
(min), the device can be selected for
READ instructions even if the t
PUW
delay is not yet
fully elapsed.
t
PUW
after V
CC
passed the V
WI
threshold
t
VSL
after V
CC
passed the V
CC
(min) level
At Power-up, the device is in the following state:
The device is in the Standby Power mode
The Write Enable Latch (WEL) bit is reset.
Normal precautions must be taken for supply rail
decoupling, to stabilize the V
CC
supply. Each de-
vice in a system should have the V
CC
rail decou-
pled by a suitable capacitor close to the package
pins. (Generally, this capacitor is of the order of
0.1μF).
At Power-down, when V
CC
drops from the operat-
ing voltage, to below the Power On Reset (POR)
threshold voltage, V
WI
, all operations are disabled
and the device does not respond to any instruc-
tion. (The designer needs to be aware that if a
Power-down occurs while a Write, Program or
Erase cycle is in progress, some data corruption
can result.)
Figure 20. Power-up Timing
VCC
AI04009C
VCC(min)
VWI
Reset State
of the
Device
Chip Selection Not Allowed
Program, Erase and Write Commands are Rejected by the Device
tVSL
tPUW
time
Read Access allowed
Device fully
accessible
VCC(max)
相關PDF資料
PDF描述
M25PE80-VMP6G 4 Mbit Uniform Sector, Serial Flash Memory
M25PE80-VMP6P 4 Mbit Uniform Sector, Serial Flash Memory
M25PE80-VMP6T 4 Mbit Uniform Sector, Serial Flash Memory
M25PE80-VMP6TG 4 Mbit Uniform Sector, Serial Flash Memory
M25PE80-VMP6TP 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25P64-VMF6TPBA 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3.3V 64Mbit 8M x 8bit 8ns 16-Pin SOIC W T/R 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel 制造商:Micron Technology Inc 功能描述:64MBIT SPI NOR FLASH 制造商:Micron Technology 功能描述:NOR Flash Serial-SPI 3.3V 64Mbit 8M x 8bit 8ns 16-Pin SOIC W T/R
M25P64-VMF6TPBA TR 制造商:Micron Technology Inc 功能描述:IC FLASH 64MBIT 75MHZ 16SO
M25P64-VMF6TP-N 制造商:STMicroelectronics 功能描述:64Mbit, Low Voltage, Serial Flash Memory With 50 MHz SPI Bus Interface
M25P80 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface
M25P80S-VMN6P 制造商:Micron Technology Inc 功能描述: 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 75MHZ 8SO