參數資料
型號: M25PE80-VMN6TG
廠商: 意法半導體
元件分類: DRAM
英文描述: 4 Mbit Uniform Sector, Serial Flash Memory
中文描述: 4兆位統一部門,串行閃存
文件頁數: 42/61頁
文件大?。?/td> 326K
代理商: M25PE80-VMN6TG
Instructions
M25PE80
42/61
6.16
Deep Power-down (DP)
Executing the Deep Power-down (DP) instruction is the only way to put the device in the
lowest consumption mode (the Deep Power-down mode). It can also be used as an extra
software protection mechanism, while the device is not in active use, since in this mode, the
device ignores all Write, Program and Erase instructions.
Driving Chip Select (S) High deselects the device, and puts the device in the Standby mode
(if there is no internal cycle currently in progress). But this mode is not the Deep Power-
down mode. The Deep Power-down mode can only be entered by executing the Deep
Power-down (DP) instruction, subsequently reducing the standby current (from I
CC1
to I
CC2
,
as specified in
Table 20
).
Once the device has entered the Deep Power-down mode, all instructions are ignored
except the Release from Deep Power-down (RDP) instruction. Issuing the Release from
Deep Power-down (RDP) instruction will cause the device to exit the Deep Power-down
mode.
The Deep Power-down mode automatically stops at Power-down, and the device always
Powers-up in the Standby mode.
The Deep Power-down (DP) instruction is entered by driving Chip Select (S) Low, followed
by the instruction code on Serial Data Input (D). Chip Select (S) must be driven Low for the
entire duration of the sequence.
The instruction sequence is shown in
Figure 22
.
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the Deep Power-down (DP) instruction is not executed. As soon as
Chip Select (S) is driven High, it requires a delay of t
DP
before the supply current is reduced
to I
CC2
and the Deep Power-down mode is entered.
Any Deep Power-down (DP) instruction, while an Erase, Program or Write cycle is in
progress, is rejected without having any effects on the cycle that is in progress.
Figure 22.
Deep Power-down (DP) instruction sequence
C
D
AI03753D
S
2
1
3
4
5
6
7
0
t
DP
Deep Power-down Mode
Stand-by Mode
Instruction
相關PDF資料
PDF描述
M25PE80-VMN6TP 4 Mbit Uniform Sector, Serial Flash Memory
M25PX32 4 Mbit Uniform Sector, Serial Flash Memory
M25PX32-VMP6E 4 Mbit Uniform Sector, Serial Flash Memory
M25PX32-VMP6F 4 Mbit Uniform Sector, Serial Flash Memory
M25PX32-VMW6E 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25PE80-VMN6TP 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25PE80-VMN6TPBA 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3.3V 8Mbit 1M x 8bit 8ns T/R 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel 制造商:Micron Technology Inc 功能描述:IC FLASH 8MX1 PBF SOIC 3.0V
M25PE80-VMP6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit, Low Voltage, Page-Erasable Serial Flash Memory with Byte-Alterability, 50MHz SPI Bus, Standard Pin-out
M25PE80-VMP6G 功能描述:閃存 8 Mbit Lo Vltg Page Erasable Seral 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25PE80-VMP6P 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:8-Mbit, page-erasable serial flash memory with byte alterability, 75 MHz SPI bus, standard pinout