- 您現在的位置：買賣IC網 > PDF目錄359029 > M29F400BT90N6 (意法半導體) 4 Mbit 512Kb x8 or 256Kb x16, Boot Block Single Supply Flash Memory PDF資料下載
參數資料
| 型號： | M29F400BT90N6 |
| 廠商： | 意法半導體 |
| 英文描述： | 4 Mbit 512Kb x8 or 256Kb x16, Boot Block Single Supply Flash Memory |
| 中文描述： | 4兆位512KB的x8或256Kb的x16插槽，啟動座單電源閃存 |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 208K |
| 代理商： | M29F400BT90N6 |
M29F400BT, M29F400BB
10/22
STATUS REGISTER
Bus Read operations from any address always
read the Status Register during Program and
Erase operations. It is also read during Erase Sus-
pend when an address within a block being erased
is accessed.
The bits in the Status Register are summarized in
Table 10, Status Register Bits.
Data Polling Bit (DQ7).
The Data Polling Bit can
be used to identify whether the Program/Erase
Controller has successfully completed its opera-
tion or if it has responded to an Erase Suspend.
The Data Polling Bit is output on DQ7 when the
Status Register is read.
During Program operations the Data Polling Bit
outputs the complement of the bit being pro-
grammed to DQ7. After successful completion of
the Program operation the memory returns to
Read mode and Bus Read operations from the ad-
dress just programmed output DQ7, not its com-
plement.
During Erase operations the Data Polling Bit out-
puts ’0’, the complement of the erased state of
DQ7. After successful completion of the Erase op-
eration the memory returns to Read Mode.
In Erase Suspend mode the Data Polling Bit will
output a ’1’ during a Bus Read operation within a
block being erased. The Data Polling Bit will
change from a ’0’ to a ’1’ when the Program/Erase
Controller has suspended the Erase operation.
Figure 4, Data Polling Flowchart, gives an exam-
ple of how to use the Data Polling Bit. A Valid Ad-
dress is the address being programmed or an
address within the block being erased.
Toggle Bit (DQ6).
The Toggle Bit can be used to
identify whether the Program/Erase Controller has
successfully completed its operation or if it has re-
sponded to an Erase Suspend. The Toggle Bit is
output on DQ6 when the Status Register is read.
During Program and Erase operations the Toggle
Bit changes from ’0’ to ’1’ to ’0’, etc., with succes-
sive Bus Read operations at any address. After
successful completion of the operation the memo-
ry returns to Read mode.
During Erase Suspend mode the Toggle Bit will
output when addressing a cell within a block being
erased. The Toggle Bit will stop toggling when the
Program/Erase Controller has suspended the
Erase operation.
Figure 5, Data Toggle Flowchart, gives an exam-
ple of how to use the Data Toggle Bit.
Error Bit (DQ5).
The Error Bit can be used to
identify errors detected by the Program/Erase
Controller. The Error Bit is set to ’1’ when a Pro-
gram, Block Erase or Chip Erase operation fails to
write the correct data to the memory. If the Error
Bit is set a Read/Reset command must be issued
before other commands are issued. The Error bit
is output on DQ5 when the Status Register is read.
Note that the Program command cannot change a
bit set at ’0’ back to ’1’ and attempting to do so may
or may not set DQ5 at ‘1’. In both cases, a succes-
sive Bus Read operation will show the bit is still ‘0’.
One of the Erase commands must be used to set
all the bits in a block or in the whole memory from
’0’ to ’1’.
Table 10. Status Register Bits
Note: Unspecified data bits should be ignored.
Operation
Address
DQ7
DQ6
DQ5
DQ3
DQ2
RB
Program
Any Address
DQ7
Toggle
0
–
–
0
Program During Erase
Suspend
Any Address
DQ7
Toggle
0
–
–
0
Program Error
Any Address
DQ7
Toggle
1
–
–
0
Chip Erase
Any Address
0
Toggle
0
1
Toggle
0
Block Erase before
timeout
Erasing Block
0
Toggle
0
0
Toggle
0
Non-Erasing Block
0
Toggle
0
0
No Toggle
0
Block Erase
Erasing Block
0
Toggle
0
1
Toggle
0
Non-Erasing Block
0
Toggle
0
1
No Toggle
0
Erase Suspend
Erasing Block
1
No Toggle
0
–
Toggle
1
Non-Erasing Block
Data read as normal
1
Erase Error
Good Block Address
0
Toggle
1
1
No Toggle
0
Faulty Block Address
0
Toggle
1
1
Toggle
0
相關PDF資料 |
PDF描述 |
|---|---|
| M29F400B | 4 Mbit 512Kb x8 or 256Kb x16, Boot Block Single Supply Flash Memory |
| M29F400B-120M1R | 4 Mbit 512Kb x8 or 256Kb x16, Boot Block Single Supply Flash Memory |
| M29F400B-120M1TR | Single Positive-Edge-Triggered D-Type Flip-Flop 5-SC70 -40 to 85 |
| M29F400B-120M3R | 4 Mbit 512Kb x8 or 256Kb x16, Boot Block Single Supply Flash Memory |
| M29F400B-120M3TR | Single Positive-Edge-Triggered D-Type Flip-Flop 5-SC70 -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M29F400BT90N6T | 功能描述:閃存 512Kx8 or 256Kx16 90 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M29F400FB55D11 | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Gel-pak, waffle pack, wafer, diced wafer on film |
| M29F400FB55M32 | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Trays |
| M29F400FB55M3E2 | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 55NS 44SO |
| M29F400FB55M3F2 | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。