參數資料
型號： M29W004BB90N6T
廠商： 意法半導體
英文描述： 4 Mbit 512Kb x8, Boot Block Low Voltage Single Supply Flash Memory
中文描述： 4兆位512KB的× 8，啟動塊低壓單電源閃存
文件頁數： 6/30頁
文件大?。?/td> 222K
代理商： M29W004BB90N6T
DEVICE OPERATIONS
See Tables 4, 5 and 6.
Read.
Read operations are used to output the
contents of the Memory Array, the Electronic Sig-
nature, the Status Register or the Block Protection
Status. Both Chip Enable E and Output Enable G
must be low in order to read the output of the
memory.
Write.
Write operations are used to give Instruction
Commands to the memory or to latch input data to
be programmed. A write operation is initiated when
Chip Enable E is Low and Write Enable W is Low
with Output Enable G High. Addresses are latched
on the falling edge of W or E whichever occurs last.
Commands and Input Data are latched on the rising
edge of W or E whichever occurs first.
Output Disable.
The data outputs are high imped-
ance when the Output Enable G is High with Write
Enable W High.
Standby.
The memory is in standby when Chip
Enable E is High and the P/E.C. is idle. The power
consumption is reduced to the standby level and
the outputs are high impedance, independent of
the Output Enable G or Write Enable W inputs.
Automatic Standby.
After 150ns of bus inactivity
and when CMOS levels are driving the addresses,
the chip automatically enters a pseudo-standby
mode where consumption is reduced to the CMOS
standby value, while outputs still drive the bus.
Electronic Signature.
Two codes identifying the
manufacturer and the device can be read from the
memory. The manufacturer’s code for STMi-
croelectronics is 20h, the device code is EAh for
the M29W004T (Top Boot) and EBh for the
M29W004B (Bottom Boot). These codes allow pro-
gramming equipment or applications to automat-
ically match their interface to the characteristics of
the M29W004. The Electronic Signature is output
by a Read operation when the voltage applied to
A9 is at V
ID
and address input A1 is Low. The
manufacturer code is output when the Address
input A0 is Low and the device code when this
input is High. Other Address inputs are ignored.
The Electronic Signature can also be read, without
raising A9 to V
ID
, by giving the memory the Instruc-
tion AS.
Block Protection.
Each block can be separately
protected against Program or Erase on program-
ming equipment. Block protection provides addi-
tional data security, as it disables all program or
erase operations. This mode is activated when both
A9 and G are raised to V
ID
and an address in the
block is applied on A13-A18. The Block Protection
algorithm is shown in Figure 14. Block protection is
initiated on the edge of W falling to V
IL
. Then after
a delay of 100
μ
s, the edge of W rising to V
IH
ends
the protection operations. Block protection verify is
achieved by bringing G, E, A0 and A6 to V
IL
and A1
to V
IH
, while W is at V
IH
and A9 at V
ID
. Under these
conditions, reading the data output will yield 01h if
the block defined by the inputs on A13-A18 is
protected. Any attempt to program or erase a pro-
tected block will be ignored by the device.
Block Temporary Unprotection.
Any previously
protected block can be temporarily unprotected in
order to change stored data. The temporary unpro-
tection mode is activated by bringing RP to V
ID
.
During the temporary unprotection mode the pre-
viously protected blocks are unprotected. A block
can be selected and data can be modified by
executing the Erase or Program instruction with the
RP signal held at V
ID
. When RP is returned to V
IH
,
all the previously protected blocks are again pro-
tected.
Block Unprotection.
All protected blocks can be
unprotected on programming equipment to allow
updating of bit contents. All blocks must first be
protected before the unprotection operation. Block
unprotection is activated when A9, G and E are at
V
ID
and A12, A15 at V
IH
. The Block Unprotection
algorithm is shown in Figure 15. Unprotection is
initiated by the edge of W falling to V
IL
. After a delay
of 10ms, the unprotection operation will end. Un-
protection verify is achieved by bringing G and E to
V
IL
while A0 is at V
IL
, A6 and A1 are at V
IH
and A9
remains at V
ID
. In these conditions, reading the
output data will yield 00h if the block defined by the
inputs A13-A18 has been succesfully unprotected.
Each block must be separately verified by giving its
address in order to ensure that it has been unpro-
tected.
6/30
M29W004T, M29W004B
相關PDF資料
PDF描述
M29W004BB90N1T 4 Mbit 512Kb x8, Boot Block Low Voltage Single Supply Flash Memory
M29W004BB70N6T 4 Mbit 512Kb x8, Boot Block Low Voltage Single Supply Flash Memory
M29W004BB70N1T Dual High-Speed JFET-Input Operational Amplifier 8-SOIC
M29W004BB55N6T 4 Mbit 512Kb x8, Boot Block Low Voltage Single Supply Flash Memory
M29W004BB55N1T 4 Mbit 512Kb x8, Boot Block Low Voltage Single Supply Flash Memory
相關代理商/技術參數
參數描述
M29W004BT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Boot Block Low Voltage Single Supply Flash Memory
M29W004BT120N1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Boot Block Low Voltage Single Supply Flash Memory
M29W004BT120N6 功能描述:閃存 4M (512Kx8) 120ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M29W004BT120N6T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Boot Block Low Voltage Single Supply Flash Memory
M29W004BT55N1 功能描述:閃存 TSOP-40 512KX8 55NS RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*