- 您現在的位置：買賣IC網 > PDF目錄377818 > M29W160DB90ZA6 (意法半導體) 16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory PDF資料下載
參數資料
| 型號： | M29W160DB90ZA6 |
| 廠商： | 意法半導體 |
| 英文描述： | 16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| 中文描述： | 16兆位（含2Mb x8或1兆x16插槽，引導塊）3V電源快閃記憶體 |
| 文件頁數： | 38/44頁 |
| 文件大?。?/td> | 333K |
| 代理商： | M29W160DB90ZA6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁
M29W160DT, M29W160DB
38/44
APPENDIX C. BLOCK PROTECTION
Block protection can be used to prevent any oper-
ation from modifying the data stored in the Flash.
Each Block can be protected individually. Once
protected, Program and Erase operations on the
block fail to change the data.
There are three techniques that can be used to
control Block Protection, these are the Program-
mer technique, the In-System technique and Tem-
porary Unprotection. Temporary Unprotection is
controlled by the Reset/Block Temporary Unpro-
tection pin, RP; this is described in the Signal De-
scriptions section.
Unlike the Command Interface of the Program/
Erase Controller, the techniques for protecting and
unprotecting blocks could change between differ-
ent Flash memory suppliers.
Programmer Technique
The Programmer technique uses high (V
ID
) volt-
age levels on some of the bus pins. These cannot
be achieved using a standard microprocessor bus,
therefore the technique is recommended only for
use in Programming Equipment.
To protect a block follow the flowchart in Figure 21,
Programmer Equipment Block Protect Flowchart.
To unprotect the whole chip it is necessary to pro-
tect all of the blocks first, then all blocks can be un-
protected at the same time. To unprotect the chip
follow Figure 22, Programmer Equipment Chip
Unprotect Flowchart. Table 29, Programmer
Technique Bus Operations, gives a summary of
each operation.
The timing on these flowcharts is critical. Care
should be taken to ensure that, where a pause is
specified, it is followed as closely as possible. Do
not abort the procedure before reaching the end.
Chip Unprotect can take several seconds and a
user message should be provided to show that the
operation is progressing.
In-System Technique
The In-System technique requires a high voltage
level on the Reset/Blocks Temporary Unprotect
pin, RP. This can be achieved without violating the
maximum ratings of the components on the micro-
processor bus, therefore this technique is suitable
for use after the Flash has been fitted to the sys-
tem.
To protect a block follow the flowchart in Figure 23,
In-System Block Protect Flowchart. To unprotect
the whole chip it is necessary to protect all of the
blocks first, then all the blocks can be unprotected
at the same time. To unprotect the chip follow Fig-
ure 24, In-System Chip Unprotect Flowchart.
The timing on these flowcharts is critical. Care
should be taken to ensure that, where a pause is
specified, it is followed as closely as possible. Do
not allow the microprocessor to service interrupts
that will upset the timing and do not abort the pro-
cedure before reaching the end. Chip Unprotect
can take several seconds and a user message
should be provided to show that the operation is
progressing.
Table 29. Programmer Technique Bus Operations, BYTE = V
IH
or V
IL
Operation
E
G
W
Address Inputs
A0-A19
Data Inputs/Outputs
DQ15A–1, DQ14-DQ0
Block Protect
V
IL
V
ID
V
IL
Pulse
A9 = V
ID
, A12-A19 Block Address
Others = X
X
Chip Unprotect
V
ID
V
ID
V
IL
Pulse
A9 = V
ID
, A12 = V
IH
, A15 = V
IH
Others = X
X
Block Protection
Verify
V
IL
V
IL
V
IH
A0 = V
IL
, A1 = V
IH
, A6 = V
IL
, A9 = V
ID
,
A12-A19 Block Address
Others = X
Pass = XX01h
Retry = XX00h
Block Unprotection
Verify
V
IL
V
IL
V
IH
A0 = V
IL
, A1 = V
IH
, A6 = V
IH
, A9 = V
ID
,
A12-A19 Block Address
Others = X
Retry = XX01h
Pass = XX00h
相關PDF資料 |
PDF描述 |
|---|---|
| M29W160DB90ZA6E | 16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DB90ZA6F | 16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DT70M1 | 16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DT70M1E | 16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DT70M1F | 16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M29W160DB90ZA6E | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DB90ZA6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DB90ZA6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DT70M1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。