參數資料
型號： M30302MAL-XXXFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100
文件頁數： 113/168頁
文件大?。?/td> 2424K
代理商： M30302MAL-XXXFP
Interrupt
46
Mitsubishi microcomputers
M16C / 30L Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Hardware Interrupts
Hardware interrupts are classified into two types — special interrupts and peripheral I/O interrupts.
(1) Special interrupts
Special interrupts are non-maskable interrupts.
Reset
____________
Reset occurs if an “L” is input to the RESET pin.
_______
NMI interrupt
_______
An NMI interrupt occurs if an “L” is input to the NMI pin.
________
DBC interrupt
This interrupt is exclusively for the debugger, do not use it in other circumstances.
Watchdog timer interrupt
Generated by the watchdog timer. Write to the watchdog timer start register after the watchdog timer
interrupt occurs (initialize watchdog timer).
Single-step interrupt
This interrupt is exclusively for the debugger, do not use it in other circumstances. With the debug
flag (D flag) set to “1”, a single-step interrupt occurs after one instruction is executed.
Address match interrupt
An address match interrupt occurs immediately before the instruction held in the address indicated by
the address match interrupt register is executed with the address match interrupt enable bit set to “1”.
If an address other than the first address of the instruction in the address match interrupt register is set,
no address match interrupt occurs.
(2) Peripheral I/O interrupts
A peripheral I/O interrupt is generated by one of built-in peripheral functions. Built-in peripheral func-
tions are dependent on classes of products, so the interrupt factors too are dependent on classes of
products. The interrupt vector table is the same as the one for software interrupt numbers 0 through
31 the INT instruction uses. Peripheral I/O interrupts are maskable interrupts.
Bus collision detection interrupt
This is an interrupt that the serial I/O bus collision detection generates.
DMA0 interrupt
This is an interrupts that DMA generates.
Key-input interrupt
___
A key-input interrupt occurs if an “L” is input to the KI pin.
A-D conversion interrupt
This is an interrupt that the A-D converter generates.
UART0, UART1, UART2/NACK transmission interrupt
These are interrupts that the serial I/O transmission generates.
UART0, UART1, UART2/ACK reception interrupt
These are interrupts that the serial I/O reception generates.
Timer A0 interrupt through timer A2 interrupt
These are interrupts that timer A generates
Timer B1, timer B2 interrupt
These are interrupts that timer B generates.
________
INT0 interrupt through INT2 interrupt
______
An INT interrupt occurs if either a rising edge or a falling edge or a both edge is input to the INT pin.
相關PDF資料
PDF描述
M30302MCL-XXXGP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
M30302MAL-XXXGP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
M30302MAL-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
M30302M8L-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
M30302MAP-XXXGP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M30302MAL-XXXGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30302MAP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30302MAP-XXX 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30302MAP-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30302MAP-XXXGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*