- 您現在的位置：買賣IC網 > PDF目錄45019 > M30625MGM-XXXGP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M30625MGM-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, QFP-80 |
| 文件頁數： | 11/25頁 |
| 文件大?。?/td> | 655K |
| 代理商： | M30625MGM-XXXGP |
Usage precaution
Mitsubishi microcomputers
M16C / 62M (80-pin version) Group
(Low voltage version)
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
18
(4) External interrupt
_______
________
When the polarity of the INT0 to INT2 pins is changed, the interrupt request bit is sometimes set
to "1". After changing the polarity, set the interrupt request bit to "0".
Example 1:
INT_SWITCH1:
FCLR
I
; Disable interrupts.
AND.B
#00h, 0055h
; Clear TA0IC int. priority level and int. request bit.
NOP
FSET
I
; Enable interrupts.
Example 2:
INT_SWITCH2:
FCLR
I
; Disable interrupts.
AND.B
#00h, 0055h
; Clear TA0IC int. priority level and int. request bit.
MOV.W MEM, R0
; Dummy read.
FSET
I
; Enable interrupts.
Example 3:
INT_SWITCH3:
PUSHC FLG
; Push Flag register onto stack
FCLR
I
; Disable interrupts.
AND.B
#00h, 0055h
; Clear TA0IC int. priority level and int. request bit.
POPC
FLG
; Enable interrupts.
The reason why two NOP instructions or dummy read are inserted before FSET I in Examples 1 and 2 is
to prevent the interrupt enable flag I from being set before the interrupt control register is rewritten due to
effects of the instruction queue.
(5) Rewrite the interrupt control register
To rewrite the interrupt control register, do so at a point that does not generate the interrupt
request for that register. If there is possibility of the interrupt request occur, rewrite the interrupt
control register after the interrupt is disabled. The program examples are described as follow:
When a instruction to rewrite the interrupt control register is executed but the interrupt is disabled,
the interrupt request bit is not set sometimes even if the interrupt request for that register has
been generated. This will depend on the instruction. If this creates problems, use the below
instructions to change the register.
Instructions : AND, OR, BCLR, BSET
Noise
(1) Insert bypass capacitor between VCC and VSS pin for noise and latch up countermeasure.
Insert bypass capacitor (about 0.1
F) and connect short and wide line between VCC and VSS
lines.
相關PDF資料 |
PDF描述 |
|---|---|
| M30621FCMGP | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP80 |
| M30626FHPGP#U9C | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| M3062AFCTFP | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| M3062CMAT-XXXFP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| M3062CM6T-XXXFP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30625MGN-A25GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30625MGN-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30625MGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30625MGP-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30625MG-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發(fā)布緊急采購，3分鐘左右您將得到回復。