- 您現在的位置：買賣IC網 > PDF目錄45023 > M306NMME-XXXGP 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP128 PDF資料下載
參數資料
| 型號： | M306NMME-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP128 |
| 封裝： | 14 X 20 MM, 0.50 MM PITCH, PLASTIC, LQFP-128 |
| 文件頁數： | 7/86頁 |
| 文件大?。?/td> | 724K |
| 代理商： | M306NMME-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
Rev.2.10
Aug 25, 2006
page 13 of 81
REJ03B0058-02100
M16C/6N Group (M16C/6NK, M16C/6NM)
1. Overview
Under development
This document is under development and its contents are subject to change.
1.6 Pin Functions
Tables 1.9 to 1.11 list the Pin Functions.
Table 1.9 Pin Functions (100-pin and 128-pin Versions) (1)
I
I/O
O
I/O
O
I
O
I
VCC1, VCC2,
VSS
AVCC, AVSS
_____________
RESET
CNVSS
BYTE
D0 to D7
D8 to D15
A0 to A19
A0/D0 to A7/D7
A1/D0 to A8/D7
_______
CS0 to CS3
_________ ______
WRL/WR
_________ ________
WRH/BHE
______
RD
ALE
__________
HOLD
__________
HLDA
________
RDY
Power supply
input
Analog power
supply input
Reset input
CNVSS
(2)
External data
bus width
select input
(2)
Bus control
pins
(3)
Apply 3.0 to 5.5 V to the VCC1 and VCC2 pins and 0 V to the VSS
pin. The VCC apply condition is that VCC2 = VCC1
(1).
Applies the power supply for the A/D converter. Connect the AVCC
pin to VCC1. Connect the AVSS pin to VSS.
The MCU is in a reset state when applying “L” to the this pin.
Switches processor mode. Connect this pin to VSS to when after
a reset to start up in single-chip mode. Connect this pin to VCC1
to start up in microprocessor mode.
Switches the data bus in external memory space. The data bus
is 16-bit long when the this pin is held “L” and 8-bit long when
the this pin is held “H”. Set it to either one. Connect this pin to
VSS when single-chip mode.
Inputs and outputs data (D0 to D7) when these pins are set as
the separate bus.
Inputs and outputs data (D8 to D15) when external 16-bit data
bus is set as the separate bus.
Output address bits (A0 to A19).
Input and output data (D0 to D7) and output address bits (A0 to
A7) by time-sharing when external 8-bit data bus are set as the
multiplexed bus.
Input and output data (D0 to D7) and output address bits (A1 to
A8) by time-sharing when external 16-bit data bus are set as the
multiplexed bus.
_______
Output CS0 to CS3 signals. CS0 to CS3 are chip-select signals
to specify an external space.
________
_________
______
________
_____
________
_________
Output WRL, WRH, (WR, BHE), RD signals. WRL and WRH or
________
______
BHE, and WR can be switched by program.
________
_________
_____
WRL, WRH, and RD are selected
________
The WRL signal becomes “L” by writing data to an even address
in an external memory space.
_________
The WRH signal becomes “L” by writing data to an odd address
in an external memory space.
_____
The RD pin signal becomes “L” by reading data in an external
memory space.
______
________
_____
WR, BHE, and RD are selected
______
The WR signal becomes “L” by writing data in an external
memory space.
_____
The RD signal becomes “L” by reading data in an external
memory space.
________
The BHE signal becomes “L” by accessing an odd address.
______
________
_____
Select WR, BHE, and RD for an external 8-bit data bus.
ALE is a signal to latch the address.
__________
While the HOLD pin is held “L”, the MCU is placed in a hold
state.
__________
In a hold state, HLDA outputs a “L” signal.
________
While applying a “L” signal to the RDY pin, the MCU is placed in
a wait state.
Signal Name
Pin Name
I/O Type
Description
I: Input
O: Output
I/O: Input/Output
NOTES:
1. In this manual, hereafter, VCC refers to VCC1 unless otherwise noted.
2. Connect to VSS in T/V-ver..
3. Not available the bus control pins in T/V-ver..
相關PDF資料 |
PDF描述 |
|---|---|
| M306NKFHTGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M306NNFHGP | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP128 |
| M306NLFHGP | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| M306NLFJGP | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| M306NNMG-XXXGP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP128 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M306NMMG-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Renesas MCU |
| M306NNFHGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Renesas MCU |
| M306NNFHGP#U3 | 功能描述:IC M16C MCU FLASH 384K 128LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/6N 產品培訓模塊:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 標準包裝:27 系列:PIC® 24H 核心處理器:PIC 芯體尺寸:16-位 速度:40 MIP 連通性:I²C，SPI，UART/USART 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:21 程序存儲器容量:12KB（4K x 24） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 3.6 V 數據轉換器:A/D 10x10b/12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 包裝:管件 產品目錄頁面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2 |
| M306NNFJGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Renesas MCU |
| M306NNFJGP#U3 | 功能描述:IC M16C/6NN MCU FLASH 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/6N 標準包裝:160 系列:S08 核心處理器:S08 芯體尺寸:8-位 速度:40MHz 連通性:I²C，LIN，SCI，SPI 外圍設備:LCD，LVD，POR，PWM，WDT 輸入/輸出數:53 程序存儲器容量:32KB（32K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1.9K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 12x12b 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:64-LQFP 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。