- 您現在的位置：買賣IC網 > PDF目錄45023 > M306V7MG-XXXFP 16-BIT, MROM, 16.1 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M306V7MG-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 16.1 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 47/300頁 |
| 文件大?。?/td> | 2323K |
| 代理商： | M306V7MG-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁第287頁第288頁第289頁第290頁第291頁第292頁第293頁第294頁第295頁第296頁第297頁第298頁第299頁第300頁
Rev.1.00
May 18, 2004
page 138 of 296
M306V7MG/MH/MJ/MJA-XXXFP, M306V7FG/FH/FJ/FJAFP
s Bit 4: I2C-BUS interface i interrupt request bit (PIN)
This bit generates an interrupt request signal. Each time 1-byte data is transmitted, the state of the
PIN bit changes from “1” to “0.” At the same time, an interrupt request signal is sent to the CPU. The
PIN bit is set to “0” in synchronization with a falling edge of the last clock (including the ACK clock) of
an internal clock and an interrupt request signal occurs in synchronization with a falling edge of the
PIN bit. When detecting the STOP condition in slave, the multi-master I2C-BUS interface interrupt
request bit (IR) is set to “1” (interrupt requested) regardless of falling of PIN bit. When the PIN bit is “0,”
the SCL is kept in the “0” state and clock generation is disabled. Figure 2.11.37 shows an interrupt
request signal generating timing chart.
The PIN bit is set to “1” in any one of the following conditions.
Writing “1” to the PIN bit
Executing a write instruction to the I2Ci data shift register or the I2Ci transmit buffer register (See note).
When the ESO bit is “0”
At reset
Note: It takes 12 BCLK cycles or more until PIN bit becomes “1” after write instructions are executed
to these registers.
The conditions in which the PIN bit is set to “0” are shown below:
Immediately after completion of 1-byte data transmission (including when arbitration lost is detected)
Immediately after completion of 1-byte data reception
In the slave reception mode, with ALS = “0” and immediately after completion of slave address or
general call address reception
In the slave reception mode, with ALS = “1” and immediately after completion of address data reception
s Bit 5: bus busy flag (BB)
This bit indicates the status of use of the bus system. When this bit is set to “0,” this bus system is not
busy and a START condition can be generated. When this bit is set to “1,” this bus system is busy and
the occurrence of a START condition is disabled by the START condition duplication prevention func-
tion (See note).
This flag can be written by software only in the master transmission mode. In the other modes, this bit is
set to “1” by detecting a START condition and set to “0” by detecting a STOP condition. When the ESO bit
of the I2Ci control register is “0” and at reset, the BB flag is kept in the “0” state.
s Bit 6: communication mode specification bit (transfer direction specification bit: TRX)
This bit decides the direction of transfer for data communication. When this bit is “0,” the reception
mode is selected and the data of a transmitting device is received. When the bit is “1,” the transmission
mode is selected and address data and control data are output into the SDA in synchronization with
the clock generated on the SCL.
When the ALS bit of the I2Ci control register is “0” in the slave reception mode is selected, the TRX bit
___
is set to “1” (transmit) if the least significant bit (R/W bit) of the address data transmitted by the master
___
is “1.” When the ALS bit is “0” and the R/W bit is “0,” the TRX bit is cleared to “0” (receive).
The TRX bit is cleared to “0” in one of the following conditions.
When arbitration lost is detected.
When a STOP condition is detected.
When occurence of a START condition is disabled by the START condition duplication prevention
function (Note).
With MST = “0” and when a START condition is detected.
With MST = “0” and when ACK non-return is detected.
At reset
相關PDF資料 |
PDF描述 |
|---|---|
| M306V7FJFP | 16-BIT, FLASH, 16.1 MHz, MICROCONTROLLER, PQFP100 |
| M306V7FGFP | 16-BIT, FLASH, 16.1 MHz, MICROCONTROLLER, PQFP100 |
| M306V7FHFP | 16-BIT, FLASH, 16.1 MHz, MICROCONTROLLER, PQFP100 |
| M30800MC-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100 |
| M30800MC-XXXGP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M306V7MH-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M306V7MJA-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M306V7MJ-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M306V7T-RPD-E | 功能描述:DEV EMULATION POD FOR M16C/6V (M RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M306V8FJFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。