SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
M37150M6/M8/MA/MC/MF-XXXFP, M37150EFFP
MITSUBISHI MICROCOMPUTERS
102
Rev. 1.0
Max.
30
45
200
2
100
10
0.4
3.0
0.4
0.6
1.3
5
130
VCC = 5.5V,
f(XIN) = 8.95MHz
VCC = 5.5V, f(XIN) = 0,
f(XCIN) = 32kHz,
OSD OFF, Data slicer OFF,
Low-power dissipation mode set
(CM5 = “0”, CM6 = “1”)
VCC = 5.5 V, f(XcIN) = 3.58 MHz
VCC = 5.5 V, f(XIN) = 0,
f(XCIN) = 32 kHz,
Low-power dissipation mode set
(CM5 = “0”, CM6 = “1”)
VCC = 5.5V, f(XIN) = 0,
f(XCIN) = 0
VCC = 4.5 V
IOH = –0.5 mA
VCC = 4.5 V
IOL = 0.5 mA
VCC = 4.5 V
IOL = 10.0 mA
VCC = 4.5 V
VCC = 5.0 V
VCC = 5.5 V
VI = 5.5 V
VCC = 5.5 V
VI = 0 V
VCC = 4.5 V
12. ELECTRIC CHARACTERISTICS (VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8.95 MHz, Ta = –10 °C to 70 °C, unless otherwise noted)
Notes 1: The total current that flows out of the IC must be 20 mA or less.
2: The total input current to IC (IOL1 + IOL2) must be 30 mA or less.
3: The total average input current for ports P24–P27 and AVCC–VSS to IC must be 20 mA or less.
4: Connect 0.1
F or more capacitor externally between the power source pins VCC–VSS so as to reduce power source noise.
Also connect 0.1
F or more capacitor externally between the pins VCC–CNVSS.
5: P06, P07, P16, P23, P24, P25 have hysteresis when used as interrupt input pins or timer input pins. P11–P14, P30, P31 have hysteresis when used as multi-
master I2C-BUS interface ports. P20–P22 have hysteresis when used as serial I/O pins.
6: Pin names in each parameter are described as below.
(1) Dedicated pins: dedicated pin names.
(2) Double-/triple-function ports
Same limits: I/O port name.
Functions other than ports vary from I/O port limits: function pin name.
HIGH output voltage
P10–P16, P20–P27,
P30, P31, P52–P55,
LOW output voltage
P00–P07, P10,
P15, P16, P20–P23,
P52–P55
LOW output voltage
P24– P27
LOW output voltage
P11–P14, P30, P32
Hysteresis (See note 6)
____________
RESET, P50, P51, INT1, INT2,
INT3, TIM2, TIM3, SIN, SCLK, SCL1,
SCL2, SCL3, SDA1, SDA2, SDA3
HIGH input leak current
P00–P07, P10–P16, P20–P27,
____________
P30, P31, RESET, P50, P51,
HIGH input leak current
P00–P07, P10–P16, P20–P27, P30,
____________
P31, P50, P51, RESET
I2C-BUS BUS switch connection resistor
(between SCL1 and SCL2, SDA1 and SDA2)
ICC
Symbol
Parametear
Test conditions
OSD OFF
Data slicer OFF
OSD ON
Data slicer ON
Stop mode
Wait mode
System operation
Power source current
VOH
VOL
VT+ –VT–
IIZH
IIZL
RBS
Test
circuit
1
Min.
2.4
Limits
IOL = 3 mA
IOL = 6 mA
Typ.
15
30
60
1
25
1
0.5
2
3
4
5
4
Unit
mA
A
mA
A
V
A