參數資料
型號： M37211M2-704SP
廠商： Mitsubishi Electric Corporation
英文描述： Hook-Up Wire; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Color:White/Black; Cable/Wire MIL SPEC:MIL-W-16878/1 Type B; Conductor Material:Copper; Jacket Material:Polyvinylchloride (PVC) RoHS Compliant: Yes
中文描述： 單芯片8位CMOS微機電壓合成與屏幕顯示控制器
文件頁數： 11/59頁
文件大小： 764K
代理商： M37211M2-704SP
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP
M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
11
Fig. 6 Structure of timer-related registers
TIMERS
The M37210M3-XXXSP has 4 timers: timer 1, timer 2, timer 3 and
timer 4. All timers are 8-bit timers with the 8-bit timer latch. The timer
block diagram is shown in Figure 7.
All of the timers count down and their divide ratio is 1/(n+1), where n
is the value of timer latch. The value is set to a timer at the same time
by writing a count value to the corresponding timer latch (addresses
00F0
16
to 00F3
16
: timers 1 to 4).
The count value is decremented by 1. The timer interrupt request bit
is set to “1” by an timer overflow at the next count pulse after the
count value reaches “00
16.
”
(1) Timer 1
Timer 1 can select one of the following count sources:
f(X
IN
)/16
f(X
IN
)/4096
The count source of timer 1 is selected by setting bit 0 of the timer 12
mode register (address 00F4
16
).
Timer 1 interrupt request occurs at timer 1 overflow.
(2) Timer 2
Timer 2 can select one of the following count sources:
f(X
IN
)/16
Timer 1 overflow signal
External clock from the P3
2
/TIM2 pin
The count source of timer 2 is selected by setting bits 4 and 1 of the
timer 12 mode register (address 00F4
16
). When timer 1 overflow
signal is a count source for the timer 2, the timer 1 functions as an 8-
bit prescaler.
Timer 2 interrupt request occurs at timer 2 overflow.
(3) Timer 3
Timer 3 can select one of the following count sources:
f(X
IN
)/16
External clock from the P3
3
/TIM3 pin and the H
SYNC
pin
The count source of timer 3 is selected by setting bits 5 and 0 of the
timer 34 mode register (address 00F5
16
).
Timer 3 interrupt request occurs at timer 3 overflow.
(4) Timer 4
Timer 4 can select one of the following count sources:
f(X
IN
)/16
f(X
IN
)/2
Timer 3 overflow signal
The count source of timer 3 is selected by setting bits 4 and 1 of the
timer 34 mode register 2 (address 00F5
16
). When timer 3 overflow
signal is a count source for the timer 4, the timer 3 functions as an 8-
bit prescaler.
Timer 4 interrupt request occurs at timer 4 overflow.
At reset, timers 3 and 4 are connected by hardware and “FF
16
” is
automatically set in timer 3; “07
16
” in timer 4. The f(X
IN
)/16 is se-
lected as the timer 3 count source. The internal reset is released by
timer 4 overflow at these state, the internal clock is connected .
At execution of the STP instruction, timers 3 and 4 are connected by
hardware and “FF
16
” is automatically set in timer 3; “07
16
” in timer 4.
However, the f(X
IN
)16 is not selected as the timer 3 count source. So
set bit 0 of the timer 34 mode register (address 00F5
16
) to “0” before
the execution of the STP instruction (f(X
IN
)16 is selected as the timer
3 count source). The internal STP state is released by timer 4 over-
flow at these state, the internal clock is connected .
Because of this, the program starts with stable clock.
The structure of timer-related registers is shown in Figure 6.
Timer 2 internal count source
selection bit
0 : f (X
IN
) /16
1 : Timer 1 overflow signal
Fix this bit to “0”
Timer 2 count stop bit
0 : Operation
1 : stop
Timer 1 count stop bit
0 : Operation
1 : Stop
Timer 2 count source selection bit
0 : Internal clock source
1 :
External clock source from
P3
2
/TIM2
pin
Timer 1 count source selection bit
0 : f (X
IN
) /16
1 : 1024
μ
s
clock
Timer 12 mode register
(TM12MR : address 00F4
16
)
7
0
Timer 3 count source selection bit
0 : f (X
IN
) /16
1 : External clock source (bits)
Timer 34 mode register
(TM34MR : address 00F5
16
)
Timer 4 internal count source
selection bit
0 : Timer 3 overflow signal
1 : f (X
IN
) /16
Timer 3 count stop bit
0 : Operation
1 : Stop
Timer 4 count stop bit
0 : Operation
1 : Stop
Timer 4 count source selection bit
0 : Internal clock source
1 : f (X
IN
) /2
7
0
Timer 3 external count source
selection bit
0 : P3
3
/TIM3 pin input
1 : H
SYNC
pin input
相關PDF資料
PDF描述
M37210M3-800SP TRANS PREBIASED PNP 200MW SOT-23
M37212 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
M37212M4 Single Chip 8 Bits Microcomputer(8位單片機)
M37212M6 Single Chip 8 Bits Microcomputer(8位單片機)
M37212M8 Single Chip 8 Bits Microcomputer(8位單片機)
相關代理商/技術參數
參數描述
M37211M2-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37212 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
M37212EFFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37212EFSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37212EFSP/FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*