43
7470/7471 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
mA
A
mA
A
V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
Ta = 25
°C
Ta = 85
°C
f(XIN)=8 MHz
f(XIN)=4 MHz
f(XIN)=8 MHz
f(XIN)=4 MHz
f(XIN)=8 MHz
f(XIN)=4 MHz
M37471M2/M4/M8-XXXSP/FP, M37471E4/E8-XXXSP/FP, M37471E8SS
ELECTRICAL CHARACTERISTICS (VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to 85
°C, unless otherwise noted)
2
1
–5
–3
–1.0
–0.35
–5
–3
–5
–3
–1.0
–0.35
–5
–3
5
3
5
3
5
3
5
3
14
7
3.6
15
8
4
80
40
4
2
1
12
8
1
10
0.5
0.3
0.5
0.3
0.5
0.3
–0.5
–0.18
–0.5
–0.18
7
3.5
1.8
7.5
4
2
30
15
2
1
0.5
3
2
0.1
1
VCC = 5 V, IOH = –5 mA
VCC = 3 V, IOH = –1.5 mA
VCC = 5 V, IOL = 10 mA
VCC = 3 V, IOL = 3 mA
VCC = 5 V
VCC = 3 V
VCC = 5 V
VCC = 3 V
Max.
Limits
Symbol
Parameter
Min.
Typ.
Unit
Test Conditions
At normal
mode, A-D
conversion is
not executed.
3
2
–0.25
–0.08
–0.25
–0.08
2
V
A
mA
A
mA
A
VOH
VOL
VT+ – VT–
VT+ –VT–
IIL
IIH
Stop all oscillation
VRAM
RAM retention voltage
Stop all oscillation
VCC = 5 V
At wait mode.
At normal
mode, A-D
conversion is
executed.
ICC
Power source current
At wait mode, XIN = 0 Hz, XCIN
= 32 kHz, XCOUT is low-power
mode, Ta=25
°C
At low-speed mode, Ta=25
°C, f(XIN)=0,
f(XCIN)=32 kHz, XCOUT drive capacity
is low, A-D conversion is not executed.
“H” output voltage
P00–P07,
P10–P17, P20–P27, P40–P43
“L” output voltage
P00–P07,
P10–P17, P20–P27, P40–P43
Hysteresis
P00–P07,
P30–P33
Hysteresis
RESET
Hysteresis
P16/CLK
“L” input current
P00–P07, P10–P17, P30–P32,
P40–P43, P50–P53
“L” input current
P33
“L” input current
RESET, XIN
“H” input current P00–P07, P10–P17,
P30–P32, P40–P43, P50–P53
“H” input current
P33
“H” input current
P20–P27
VI = 0 V,
not use pull-up transistor
VI = 0 V,
use pull-up transistor
VI = 0 V
used as CLK input
VI = 0 V, not use as analog input,
not use pull-up transistor
VI = 0 V, not use as analog input,
use pull-up transistor
VI = 0 V
(XIN is at stop mode)
VI = VCC,
not use pull-up transistor
VI = VCC
VI = VCC, not use as analog input,
not use pull-up transistor
VI = VCC,
(XIN is at stop mode)
“L” input current
P20–P27
“H” input current
RESET, XIN