- 您現在的位置：買賣IC網 > PDF目錄45033 > M37481E8FP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | M37481E8FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | 10 X 10 MM, 0.80 MM PITCH, PLASTIC, QFP-44 |
| 文件頁數： | 20/100頁 |
| 文件大小： | 1457K |
| 代理商： | M37481E8FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
23
MITSUBISHI MICROCOMPUTERS
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
same time.
At writing only to the timer latch, when the write timing for the
timer latch is almost equal to the underflow timing, the value
that is set in the timer may not be constant.
q Read Control for Timer X/Timer Y
When the pulse cycle measurement mode or pulse width mea-
surement mode is selected, the timer value cannot be read out.
In the other modes, the timer value can be read regardless of
count operation and count stop. However, the timer latch value
cannot be read out.
q Note on CNTR0, CNTR1, INT0, INT1 Interrupt Polarity Selection
When the CNTR0/CNTR1 edge selection bit or INT0/INT1 inter-
rupt edge selection bit is set, this affects the respective interrupt
polarity.
n
(n + m)
(7) PWM Mode
q Mode Selection
This mode is selected by setting b2, b1 and b0 of TXM or TYM
to “110”.
q Count Source Selection
The count source is f(XIN)/2, f(XIN)/8 or f(XIN)/16.
q Interrupt
At the rising edge of the CNTR0/CNTR1 output, set the timer X
interrupt request bit (b0) or timer Y interrupt request bit (b1) of
IREQ1 to “1”.
q Explanation of Operation
In the case of timer X, the PWM waveform is output from the
CNTR0 pin. In the case of timer Y, the PWM waveform is output
from the CNTR1 pin.
The PWM waveform “H” period is determined by the setting
value n (n=0 to 255) of TXH or TYH. The “L” period is deter-
mined by the setting value m (m=0 to 255) of TXL or TYL.
The PWM cycle is as follows:
PWM cycle = (n + m) ! ts
PWM output duty =
ts: Timer X/timer Y count source cycle
While a timer operation stops
The timer value is set in TXL, TXH, TYL and TYH by writing to
the timer and timer latch at the same time. The output of the
CNTR0/CNTR1 pin is initialized to “H” by setting this timer value.
While a timer operation is enabled
When b1 and b0 of TXYCON are set to “0”, “H” is output during
the period of the setting value of TXH or TYH. After that, “L” is
output during the period of the setting value of TXL or TYL.
Then, these operations will be repeated. The PWM output sub-
sequent to an underflow can be changed by setting the timer
value in TXL, TXH, TYL, TYH by writing only to the timer latch.
In this mode, set the port in common with the CNTR0/CNTR1
pin as an output port.
s Note
q When the PWM “H” period is set to “0016”, the PWM output is
always “L” level.
q When the PWM “L” period is set to “0016”, the PWM output is al-
ways “H” level.
q When the PWM “H” period is set to “0016” and the “L” period is
set to “0016”, the PWM output is always “L” level.
q When at least one of the PWM “H” period and “L” period is set
to “0016”, a timer X interrupt request/timer Y interrupt request
does not occur.
q When the timer latch is set at “0016”, the timer counts down, so
its value is not constant.
Figure 25 shows a timing diagram in the PWM mode.
s Note on All Modes
q Write Control for Timer X, Timer Y
Timer X and timer Y can select either writing to both timer latch
and timer or writing only to the timer latch by b3 of TXM or TYM.
At writing only to the timer latch, a value is set in the timer latch
by writing the value in the timer X/timer Y address, so the timer
is updated at the next underflow. After reset release, writing to
both the timer latch and timer is selected.
At this status, when a value is written in the timer X/timer Y ad-
dress, the value is set in both the timer and timer latch at the
相關PDF資料 |
PDF描述 |
|---|---|
| M37480E8T-XXXFP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO32 |
| M37481E8-XXXSP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP42 |
| M37480M2T-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37480E8SP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37480E8-XXXSP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37481E8SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37481E8SS | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 16KB EPROM 5V 42PIN SDIP - Bulk |
| M37481E8T | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37481E8T-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 7470 SERIES |
| M37481E8T-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。