- 您現在的位置：買賣IC網 > PDF目錄45033 > M37513EFFS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC100 PDF資料下載
參數資料
| 型號： | M37513EFFS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC100 |
| 封裝： | WINDOWED, GLASS SEALED, CERAMIC, LCC-100 |
| 文件頁數： | 14/65頁 |
| 文件大?。?/td> | 845K |
| 代理商： | M37513EFFS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
21
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
7513 Group
INTERRUPTS
Interrupts occur by seventeen sources: seven external, nine inter-
nal, and one software.
Interrupt Control
Each interrupt except the BRK instruction interrupt has both an in-
terrupt request bit and an interrupt enable bit, and is controlled by
the interrupt disable flag. An interrupt occurs if the corresponding
interrupt request and enable bits are “1” and the interrupt disable
flag is “0”. Interrupt enable bits can be set or cleared by software.
Interrupt request bits can be cleared by software, but cannot be
set by software. The BRK instruction interrupt and reset cannot be
disabled with any flag or bit. The I flag disables all interrupts ex-
cept the BRK instruction interrupt and reset. If several interrupts
requests occurs at the same time, the interrupt with highest prior-
ity is accepted first.
Interrupt Operation
Upon acceptance of an interrupt the following operations are auto-
matically performed:
1. The contents of the program counter and processor status
register are automatically pushed onto the stack.
2. The interrupt disable flag is set and the corresponding
interrupt request bit is cleared.
3. The interrupt jump destination address is read from the vec-
tor table into the program counter.
sNotes
When setting the followings, the interrupt request bit may be set to
“1”.
When setting external interrupt active edge
Related register: Interrupt edge selection register (address 3A16)
Timer X mode register (address 2716)
Timer Y mode register (address 2816)
When switching interrupt sources of an interrupt vector address
where two or more interrupt sources are allocated
Related register: A-D control register (address 003116)
Notes1: Vector addresses contain interrupt jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
Table 8 Interrupt vector addresses and priority
Remarks
Interrupt Request
Generating Conditions
At reset
At detection of either rising or
falling edge of INT0 input
At detection of either rising or
falling edge of INT1 input
At completion of serial I/O1 data
reception
At completion of serial I/O1
transmit shift or when transmis-
sion buffer is empty
Interrupt Source
Low
High
Priority
Vector Addresses (Note 1)
Reset (Note 2)
INT0
INT1
Serial I/O1
reception
Serial I/O1
transmission
Timer X
Timer Y
Timer 2
Timer 3
CNTR0
CNTR1
Timer 1
INT2
Serial I/O2
Key input
(Key-on wake-up)
ADT
A-D conversion
BRK instruction
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
FFFD16
FFFB16
FFF916
FFF716
FFF516
FFF316
FFF116
FFEF16
FFED16
FFEB16
FFE916
FFE716
FFE516
FFE316
FFE116
FFDF16
FFDD16
FFFC16
FFFA16
FFF816
FFF616
FFF416
FFF216
FFF016
FFEE16
FFEC16
FFEA16
FFE816
FFE616
FFE416
FFE216
FFE016
FFDE16
FFDC16
At timer X underflow
At timer Y underflow
At timer 2 underflow
At timer 3 underflow
At detection of either rising or
falling edge of CNTR0 input
At detection of either rising or
falling edge of CNTR1 input
At timer 1 underflow
At detection of either rising or
falling edge of INT2 input
At completion of serial I/O2 data
transmission or reception
At falling of conjunction of input
level for port P2 (at input mode)
At either rising or falling edge of
ADT input
At completion of A-D conversion
At BRK instruction execution
Non-maskable
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
Valid when serial I/O1 is selected
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
Valid when serial I/O2 is selected
External interrupt
(valid at falling)
External interrupt (Valid when ADT
interrupt is selected
Valid when A-D interrupt is se-
lected
Non-maskable software interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| M37513M8-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| M37513EFFS | 8-BIT, UVPROM, 4 MHz, MICROCONTROLLER, CQCC100 |
| M37513M8-XXXGP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100 |
| M37513EFGP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP100 |
| M37516E6HP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37513EF-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37513M1-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37513M2-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37513M3-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37513M4-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。