- 您現在的位置：買賣IC網 > PDF目錄201874 > M37531M4T-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 PDF資料下載
參數資料
| 型號： | M37531M4T-XXXSP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| 封裝： | 0.400 INCH, PLASTIC, SDIP-32 |
| 文件頁數： | 144/215頁 |
| 文件大?。?/td> | 1365K |
| 代理商： | M37531M4T-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁當前第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁
HARDWARE
7531 Group User’s Manual
1-20
Interrupts
Interrupts occur by 12 different sources : 4 external sources, 7 inter-
nal sources and 1 software source.
Interrupt control
All interrupts except the BRK instruction interrupt have an interrupt
request bit and an interrupt enable bit, and they are controlled by the
interrupt disable flag. When the interrupt enable bit and the interrupt
request bit are set to “1” and the interrupt disable flag is set to “0”, an
interrupt is accepted.
The interrupt request bit can be cleared by program but not be set.
The interrupt enable bit can be set and cleared by program.
It becomes usable by switching CNTR0 and AD conversion interrupt
sources with bit 7 of the interrupt edge selection register, timer 2 and
serial I/O2 interrupt sources with bit 6, timer X and key-on wake-up
interrupt sources with bit 5, and serial I/O1 transmit and INT1 inter-
rupt sources with bit 4.
The reset and BRK instruction interrupt can never be disabled with
any flag or bit. All interrupts except these are disabled when the in-
terrupt disable flag is set.
When several interrupts occur at the same time, the interrupts are
received according to priority.
Interrupt operation
Upon acceptance of an interrupt the following operations are auto-
matically performed:
1. The processing being executed is stopped.
2. The contents of the program counter and processor status regis-
ter are automatically pushed onto the stack.
3. The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
4. Concurrently with the push operation, the interrupt destination
address is read from the vector table into the program counter.
Notes on use
When the active edge of an external interrupt (INT0, INT1,CNTR0) is
set, the interrupt request bit may be set.
Therefore, please take following sequence:
1. Disable the external interrupt which is selected.
2. Change the active edge in interrupt edge selection register. (in
case of CNTR0: Timer X mode register)
3. Clear the set interrupt request bit to “0”.
4. Enable the external interrupt which is selected.
Table 6 Interrupt vector address and priority
Vector addresses (Note 1)
High-order
FFFD16
FFFB16
FFF916
FFF716
FFF516
FFF316
FFF116
FFEF16
FFED16
Priority
1
2
3
4
5
6
7
8
9
Low-order
FFFC16
FFFA16
FFF816
FFF616
FFF416
FFF216
FFF016
FFEE16
FFEC16
Interrupt request generating conditions
At reset input
At completion of serial I/O1 data receive
At completion of serial I/O1 transmit shift or
when transmit buffer is empty
At detection of either rising or falling edge
of INT1 input
At detection of either rising or falling edge
of INT0 input
At timer X underflow
At falling of conjunction of input logical
level for port P0 (at input)
At timer 1 underflow
At timer 2 underflow
At completion of transmit/receive shift
At detection of either rising or falling edge
of CNTR0 input
At completion of A-D conversion
At BRK instruction execution
Remarks
Non-maskable
Valid when serial I/O1 is selected
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt (valid at falling)
STP release timer underflow
External interrupt (active edge
selectable)
Non-maskable software interrupt
Interrupt source
Reset (Note 2)
Serial I/O1
receive
Serial I/O1
transmit
INT1 (Note 3)
INT0
Timer X
Key-on wake-up
Timer 1
Timer 2
Serial I/O2
CNTR0
A-D conversion
BRK instruction
Note 1: Vector addressed contain internal jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
3: It is an interrupt which can use only for 36 pin version.
FUNCTIONAL DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC908RK2DWR2 | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC05J5ADW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC05J5AJP | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP16 |
| MC68HC05J5AP | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP20 |
| MICD-038-03.75-TTR-TTL-1-S | INTERCONNECTION DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37531RSS | 制造商:Mitsubishi Electric 功能描述: |
| M37531T-ADS | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Temporary Target Board |
| M37532E8FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37532M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37532M4-A17GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。